2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

If you are not satisfied with your factory radio since it cannot be compatible with some modern or upgraded features, it is suggested that you can replace your factory radio with a new aftermarket car radio. If you wonder how to install a 2007 2008 2009 2010-2013 Honda Fit car radio, then you can carefully read the following installation instruction on a 2007 2008 2009 2010-2013 Honda Fit car radio. Wish it is helpful for you.

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2007 2008 2009 2010-2013 Honda Fit car radio installation instruction

1. Open the glove box at first.

Open the glove box at first

Open the glove box at first

2. Remove the four screws of gloves box as these pictures show.

Remove the four screws of gloves box as these pictures show

Remove the four screws of gloves box as these pictures show

2-2

2-2

2-3

2-3

3. Unscrew the two bolts under the radio.

Unscrew the two bolts under the radio

Unscrew the two bolts under the radio

3-2

3-2

4. Take out the original car radio.

Take out the original car radio

Take out the original car radio

5. Remove the original car radio.

Remove the original car radio

Remove the original car radio

6. Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio

Disconnect all connectors at the back of the original car radio

7. Remove screws of air condition as these pictures show.

Remove screws of air condition as these pictures show

Remove screws of air condition as these pictures show

7-2

7-2

7-3

7-3

8. Pull out the air outlet of air condition.

Pull out the air outlet of air condition

Pull out the air outlet of air condition

9. Remove the hazard warning switch light.

Remove the hazard warning switch light

Remove the hazard warning switch light

10. Install the air outlet with the unit.

11. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

12. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

13. Connect the Seicane car radio to your original car radio’s plugs.

14. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

15. Put the new Seicane radio into the dash.

16. Put everything into their original place. All the installation is done.

 

If you have any doubts, please feel free to consult your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard to finish the whole installation process, you’d better arrange a professional technician to help you install the new car radio straightly. Besides, if you don’t know how to select a suitable car stereo for your car, I’d like to recommend an amazing 2007 2008 2009 2010-2013 Honda Fit car radio from Seicane to you. For more details, please click:

https://www.seicane.com/2007-2008-2009-2013-honda-fit-android-hd-touchscreen-gps-navigation-system-with-bluetooth-wifi-mirror-link-steering-wheel-control-s0402

This powerful car radio is running on the stable Android 6.1 operation system and high-quality quad-core CPU processor.

Even though you are not good at identifying directions, the high-accuracy 3D GPS navigation system is specially built in to offer you some help. With the help of the worldwide real-time navigation, you can get access to features like current location, 3D street view, landmark building display, turn-by-turn voice directions, etc. So you can be accurately guided to arrive at your desired destinations.

Additionally, under the wireless Bluetooth technology, without taking your hands off the steering wheel, both Bluetooth hands-free phone calls and Bluetooth streaming music are available as long as you pair your Bluetooth-enabled mobile phone with this unit.

Wish you like this multifunctional car radio and good luck to you!

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio after installation

As an owner of 2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93,would you like to try to remove your factory radio so as to install a new car radio? Or would you like to learn some skills for the car radio installation? If your answers toward these questions are all “yes”, then you might as well refer to the following 2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 car radio installation instruction from Seicane. Wish it is helpful for you to some extent.

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio after installation

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 car radio installation instruction

1. The original dashboard before installation.

The original dashboard before installation

The original dashboard before installation

2. Pry the panel off with a lever. You need to lift the air-conditioning assembly and don’t pry the air-conditioning panel off directly.

Pry the panel off with a lever. You need to lift the air-conditioning assembly and don't pry the air-conditioning panel off directly

Pry the panel off with a lever. You need to lift the air-conditioning assembly and don’t pry the air-conditioning panel off directly

3. Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out.

Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out

Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out

3-1

3-1

4. Disconnect the power plug behind the CD player and the plug of the radio aerials.

Disconnect the power plug behind the CD player and the plug of the radio aerials

Disconnect the power plug behind the CD player and the plug of the radio aerials

4-1

4-1

5. Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8).

Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8)

Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8)

6. Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel.

Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel

Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel

7. Check all the accessories for the new Seicane stereo.

8. Connect the harnesses to the back of the new Seicane stereo.

9. Connect the Seicane stereo to your original radio’s plugs.

10. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane stereo into the dash.

12. Put everything into their original place.

 

Wish you can gain some help from the above installation guide. If you meet any problems and don’t know how to deal with these problems, you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard for you to remove the factory radio and install the new car radio by yourself, you can directly go to a car radio upgrade center and arrange a professional technician to help you.

As for the selection of an ideal car radio, if you don’t know how to select a compatible car radio for your beloved car, you can refer to the following link which is a remarkable 2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 car radio from Seicane. For more information, please click:

https://www.seicane.com/2005-2006-2007-2008-2012-bmw-3-series-e90-e91-e92-e93-manual-air-android-bluetooth-radio-dvd-player-head-unit-support-gps-navi-hd-touchscreen-rearview-camera-wifi-usb-mirror-link-1080p-video-s32733f

This car radio’s operation system has been upgraded to the most advanced Android 8.0 operation system and it is loaded with the eight-core CPU processor as well as 4GB RAM and 32GB ROM. Thanks to the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system of high accuracy, you can easily know where you are currently and have the most suitable route option to reach your desired destinations. Additionally, this unit also comes with dual zone function, which enables you to listen to your favorite music while navigating, and the music will automatically switch to GPS voice.

Under the wireless Bluetooth technology, you can pair your Bluetooth-enabled mobile phone and this car radio, so you can dial, answer, reject and mute hands-free phone calls as well as enjoy Bluetooth streaming music from your phone playlist.

Wish you like this unit and good luck to you!

2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation

If you plan to upgrade your factory radio so as to reduce budget by yourself, it is suggested that you should find a correct installation instruction and follow it to deal with the car radio removal and installation. The following is a 2006 2007 2008 2009-2011 Honda Civic car radio installation instruction. If you own the same or similar dashboard, you can take this instruction as a reference. Wish it is helpful for you to some extent.

2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation

2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation

Before and during installation, you should notice:

1. Before connecting,please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire,so when replace the fuse, please consult the professional.

7. For your convenience, here’s there commended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 2008 2009-2011 Honda Civic car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Pry the cover of the slot below the CD player with a lever and remove it.

Pry the cover of the slot below the CD player with a lever and remove it

Pry the cover of the slot below the CD player with a lever and remove it

3. Remove two screws inside the slot with a ninety-degree screwdriver.

Remove two screws inside the slot with a ninety-degree screwdriver

Remove two screws inside the slot with a ninety-degree screwdriver

4. Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel.

Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel

Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel

5. Remove one screw in the dash.

Remove one screw in the dash

Remove one screw in the dash

6. Remove the vent panel.

Remove the vent panel

Remove the vent panel

7. Unplug the connectors beneath the panel.

Unplug the connectors beneath the panel

Unplug the connectors beneath the panel

8. Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash.

Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash

Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash

9. Unplug the connectors at the back of the original radio.

Unplug the connectors at the back of the original radio

Unplug the connectors at the back of the original radio

9-1

9-1

10. Disconnect the antenna and the other connector on the other side of the original radio.

Disconnect the antenna and the other connector on the other side of the original radio

Disconnect the antenna and the other connector on the other side of the original radio

10-1

10-1

11. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

12. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

13. Connect the Seicane car stereo to your original car radio’s plugs.

14. Put the new Seicane car stereo into the dash.

15. Turn on the new Seicane car stereo and check whether the unit is working properly.

 

Wish you can get some help from the above installation guide. If you have any doubts, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. Besides, if you still think the installation process is too complicated, you can directly arrange a professional from Seicane to help you. Anyway, before installation, you should select an ideal car radio for your beloved car. If you have no ideas, here I would like to recommend a remarkable 2006 2007 2008 2009-2011 Honda Civic car radio from Seicane to you. Here comes the link, please click:

https://www.seicane.com/hd-touch-screen-android-gps-navigation-radio-for-2006-2011-honda-civic-with-bluetooth-wifi-obd2-usb-audio-aux-1080p-rearview-camera-s0411

Loaded with the advanced and stable Android 6.1 operation system and a powerful quad-core CPU processor, this car radio has greatly enhance its capabilities and performance. So with this car radio, you can gain a much smoother, faster and easier operation experience.

Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system of high accuracy, it will be much easier for you to locate where yo are currently and have the most suitable route option to reach your desired destinations.

Additionally, as long as you connect your Bluetooth-enabled mobile phone to this car radio, you are able to get access to Bluetooth hands-free phone calls as well as listen to streaming music for more convenience and enjoyment without taking your hands off the steering wheel.

If you like this unit, just add it to your shopping cart. Good luck!

2013 2014 Toyota Vios Car Radio after installation

There is no denying that with an ideal car radio in your car, your driving experience will be improved to a large extent. However, your factory radio may not satisfy you since it has been used for a long time and its performance is not high. Under this circumstance, you can think about replacing your factory radio with a new aftermarket car radio. While for the installation, if you would like to gain a general understanding of it, you can refer to a related installation guide. The following is a 2013 2014 Toyota Vios car radio installation instruction from Seicane which can be taken as your reference.

2013 2014 Toyota Vios Car Radio after installation

2013 2014 Toyota Vios Car Radio after installation

Here are some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2013 2014 Toyota Vios car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Remove the panel with your hands,please use a plastic removal tool if necessary.

Remove the panel with your hands,please use a plastic removal tool if necessary

Remove the panel with your hands,please use a plastic removal tool if necessary

2-1

2-1

3. Disconnect the connector at the back of the air vent.

Disconnect the connector at the back of the air vent

Disconnect the connector at the back of the air vent

4. Use a screwdriver to remove four screws that are holding the original car radio.

Use a screwdriver to remove four screws that are holding the original car radio

Use a screwdriver to remove four screws that are holding the original car radio

5. Gently take out the original car radio from thedashboard.

6. Unplug the connectors and cables at the back of the original car radio.

Unplug the connectors and cables at the back of the original car radio

Unplug the connectors and cables at the back of the original car radio

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original car radio’s plugs.

10. Put the new Seicane car radio into the dash.

11. Turn on the new Seicane car radio and have a comprehensive check if it works well.

12. Install 4 screws back to their original position.

13. Install the trim panel back to its original place.

 

Wish you learn some useful skills from the above installation steps. If you meet any problems you don’t know how to deal with, please don’t worry. You can seek help from your dealer, someone experienced or a professional. Or if you still think it hard to install the new car radio, you can straightly arrange a professional technician to help install the new car radio. Anyway, before installation, please do carefully select an ideal car radio for your beloved car. If you have no ideas, you can refer to the following link which is a smart 2013 2014 Toyota Vios car radio from Seicane. For more details, please click:

https://www.seicane.com/2013-2014-toyota-vios-hd-touchscreen-android-radio-gps-navigation-system-with-bluetooth-wifi-1080p-video-dvr-mirror-link-s0452

Loaded with the stable Android 6.1 operation system and a high-quality quad-core CPU processor, this car radio from Seicane can be regarded as one of the best replacements for your factory radio.

When you get it installed in your car, you will find that almost all your different needs can be met since it comes with a wide range of comprehensive features, including 3D GPS navigation, FM/AM radio tuner, Bluetooth hands-free calls, Bluetooth streaming music, file management, USB & SD card connection, etc.

Thanks to the turn-by-turn directions and voice prompts provided by the high-end GPS navigation system, you are able to know your current locations and find the right way to reach your ideal destinations.

Besides, this car radio also comes with entertainment features to bring you fun.

Just quickly add this car radio to your shopping cart if you like it.

2006 2007 2008 2009-2011 Honda CRV car radio after installation

Nowadays, as for most car owners, what they would like to pursue if what most car owners is to have great fun all the way and a comfortable in-car environment. In order to realize this goal, in my opinion, it will be a great idea for you to remove your factory radio and install a new car radio which comes with a wide range of comprehensive features can meet your various needs in car. If you have a 2006 2007 2008 2009-2011 Honda CRV and plan to upgrade your factory radio, it is suggested that you can refer to the following 2006 2007 2008 2009-2011 Honda CRV car radio installation instruction so as to have a general understanding of the car radio installation.

2006 2007 2008 2009-2011 Honda CRV car radio after installation

2006 2007 2008 2009-2011 Honda CRV car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 2008 2009-2011 Honda CRV car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Start with placing the key in the ignition, setting the parking brake and shifting it to a lower gear.

3. When you look closely, you will find there is a little notch at the side of the a/c control. Use a flat head plastic removal tool to pry the a/c control and then remove it.

When you look closely, you will find there is a little notch at the side of the a/c control. Use a flat head plastic removal tool to pry the a/c control and then remove it

When you look closely, you will find there is a little notch at the side of the a/c control. Use a flat head plastic removal tool to pry the a/c control and then remove it

3-1

3-1

4. Move up to the top, pry the little slot, push the panel up, lift it up and then remove it.

Move up to the top, pry the little slot, push the panel up, lift it up and then remove it

Move up to the top, pry the little slot, push the panel up, lift it up and then remove it

5. Grab the back edge and tuck forward to release the panel with emergency flashes.

Grab the back edge and tuck forward to release the panel with emergency flashes

Grab the back edge and tuck forward to release the panel with emergency flashes

6. Remove all the mounting screws for the radio.

Remove all the mounting screws for the radio

Remove all the mounting screws for the radio

7. Pull the original radio out from the dash.

Pull the original radio out from the dash

Pull the original radio out from the dash

8. Disconnect the connectors and cables at the back of the radio.

9. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

10. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Wish the above installation steps can be helpful for you. If you meet any problems, you may contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can straightly go to a car radio upgrade center to arrange a professional technician to help you install the new car radio. While for the selection of the car radio, if you have no ideas, you can refer to the following link which is an amazing 2006 2007 2008 2009-2011 Honda CRV car radio from Seicane. For more information, please click:

https://www.seicane.com/hd-touchscreen-radio-android-head-unit-for-2006-2011-honda-crv-car-stereo-gps-navigation-system-bluetooth-phone-wifi-support-1080p-video-obdii-steering-wheel-control-usb-h602

Under the guidance of the turn-by-turn direction and voice prompts provide by the high-end 3D GPS navigation system of high accuracy, you will find it very easy for you to know your current locations and navigate to any locations you would like to go to. Thus, with this car radio, you will not get lost any longer.

What’s more, you can utilize this unit’s Bluetooth function fully. As long as you connect your Bluetooth-enabled mobile phone to this car radio, you will be able to get access to both Bluetooth hands-free phone calls and Bluetooth streaming music from your mobile phone.

Additionally, you can also add a one din DVD player to this car radio, and take full advantage of it to play music, videos, TV programs, movies, etc to relax both yourself and your passengers in car.

What are you waiting for? This car radio is at a reasonable price right now. Be quick to add it to your shopping cart!

2010 2011 2012 2013 Mitsubishi ASX car radio after installation

If you think your factory radio is too outdated to meet your needs in car, you can consider replacing your factory radio with a multifunctional car radio which can support a wide range of practical and entertainment features in your car. If you want to install the new car radio on your own, you can find a step-by-step installation guide to help you. The following is a step-by-step    2010 2011 2012 2013 Mitsubishi ASX car radio installation guide from Seicane, which can be taken as your reference if you have the same or similar dashboard.

2010 2011 2012 2013 Mitsubishi ASX car radio  after installation

2010 2011 2012 2013 Mitsubishi ASX car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2010 2011 2012 2013 Mitsubishi ASX car radio installation guide

1. The original car radio.

The original car radio

The original car radio

2. Use a plastic knife to pry the trim panel and remove it.

Use a plastic knife to pry the trim panel and remove it

Use a plastic knife to pry the trim panel and remove it

2-1

2-1

2-2

2-2

3. Remove screws that are holding the radio.

Remove screws that are holding the radio

Remove screws that are holding the radio

4. Take out the original car radio.

Take out the original car radio

Take out the original car radio

5. Disconnect the connectors and cables at the back of the radio.

Disconnect the connectors and cables at the back of the radio

Disconnect the connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation instruction. If you have any doubts about your car radio or the installation process, please feel free to contact your dealer, communicate with someone experienced or turn o a professional for help.

Besides, to help you effectively select an ideal car radio, here I would like to share an amazing 2010 2011 2012 2013 Mitsubishi ASX car radio from Seicane with you. For more information, you can click:

https://www.seicane.com/inch-android-2010-2013-mitsubishi-asx-radio-gps-navigation-bluetooth-obd2-4g-wifi-steering-wheel-control-backup-camera-mirror-link-16g-flash-cpu-quad-core-s301132

This car radio is running on the stable Android 6.1 operation system and a high-quality CPU processor, which will provide its users a brand new driving experience. Besides, this unit also comes with a lot of practical and entertainment features to meet your different needs in you. Therefore, this car radio can be regarded as one of the best replacements for your old factory radio.

About the practical features, one of the highlights is the high-end GPS navigation system. With the assistance of the high-end 3D GPS navigation system, through the turn-by-turn directions and voice prompts, you can easily know where you are currently and quickly find the right way to reach your ideal destinations.

Besides, you can connect your Bluetooth-enabled mobile phone to this car radio so as to get access to both Bluetooth hands-free phone calls as well as Bluetooth streaming music without taking you hands off the steering wheel ,so you can gain a lot of convenience and enjoyment.

If you like this car radio, please don’t hesitates to add it to your shopping cart right now!

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner Car Radio after installation

You may not get not so satisfied with your factory radio since it has been used for a long time and its features may not be advanced enough. IF you would like to get more convenience and enjoyment in your beloved car, it is suggested that you should remove your factory radio and try to replace a new aftermarket car radio. As for the installation, here I’d like to share a 2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio installation instruction from Seicane with you. If you own the same or similar dashboard, you can refer to the following instruction carefully.

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner Car Radio after installation

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner Car Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio installation instruction

1. The original dashboard before installation.

The original dashboard before installation

The original dashboard before installation

2. Pry the panel off with a lever. You need to lift the air-conditioning assembly and don’t pry the air-conditioning panel off directly.

Pry the panel off with a lever. You need to lift the air-conditioning assembly and don't pry the air-conditioning panel off directly

Pry the panel off with a lever. You need to lift the air-conditioning assembly and don’t pry the air-conditioning panel off directly

3. Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out.

Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out

Unplug the air-conditioning assembly. Then unscrew the CD player and pull the CD player out

3-1

3-1

4. Disconnect the power plug behind the CD player and the plug of the radio aerials.

Disconnect the power plug behind the CD player and the plug of the radio aerials

Disconnect the power plug behind the CD player and the plug of the radio aerials

4-1

4-1

5. Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8).

Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8)

Take off the plastic bracket frame behind the CD player. Six screws are shown in the picture as follow. 4 of them are T20 screws, 2 of them are turnbuckles (no.8)

6. Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel.

Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel

Unscrew the 2 turnbuckles (no.8).After the removal, the bracket is not needed, because the DVD comes with its metal bracket panel

7. Check all the accessories for the new Seicane stereo.

8. Connect the harnesses to the back of the new Seicane stereo.

9. Connect the Seicane stereo to your original radio’s plugs.

10. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane stereo into the dash.

12. Put everything into their original place.

 

Wish the above installation instruction can help you with the removal and installation to some extent. If you meet any problems you don’t know how to deal with independently, you can contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you are afraid of making damage to either your car radio or your car, you can straightly go to a car radio upgrade center and ask a professional technician to help you install the new car radio.

Besides, as for the selection of an ideal car radio, you can refer to the following link which is a remarkable 2005 2006 2007 2008-2012 BMW 3 Series E90 E91 E92 E93 Manual Air-conditioner car radio from Seicane. For more details, please click:

https://www.seicane.com/2005-2006-2007-2008-2012-bmw-3-series-e90-e91-e92-e93-manual-air-android-bluetooth-radio-dvd-player-head-unit-support-gps-navi-hd-touchscreen-rearview-camera-wifi-usb-mirror-link-1080p-video-s32733f

Upgraded to the most advanced and stable Android 8.0 operation system, this car radio also comes with a powerful eight-core CPU processor, so you can effectively embrace a much smoother, faster and easier operation experience.

With the assistance of the worldwide real-time GPS navigation system provided by this powerful car radio, you can easily know where you are currently and effectively plan the route option to get to your desired destinations punctually. And this car radio comes with dual zone function, which enables you to freely listen to your favorite music while navigating. Thus, you will gain a lot of convenience and enjoyment while navigating.

Besides, under the wireless Bluetooth technology, you can connect your Bluetooth-enabled mobile phone to this car radio so as to dial, answer, reject and mute hands-free calls as well as listen to Bluetooth streaming music.

If you like this car radio, just don’t forget to add it to your shopping cart!

2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio after installation

As the technology rapidly develops, an ideal car radio should be compatible with a higher performance and various functions. If your factory radio can not support many modern features, then it is wise of you to replace your factory radio with a new aftermarket car radio. This article will mainly introduce how to remove the factory radio and install the new aftermarket car radio for 2011 2012 2013 2014 2015 2016 JEEP Wrangler. If you have the same or similar dashboard,  you can refer to this instruction carefully.

2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio after installation

2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio after installation

Here are some tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and www.seicane.com make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

 

2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio installation instruction

1. Get the window control out of the original place, so that you can get access to the screw that is behind it.

Get the window control out of the original place, so that you can get access to the screw that is behind it

Get the window control out of the original place, so that you can get access to the screw that is behind it

2. Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control.

Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control

Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control

2-1

2-1

3. You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out.

You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out

You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out

3-1

3-1

4. There is a clip and you need to push it down and make it come right off, after that, put this window control to the side.

There is a clip and you need to push it down and make it come right off, after that, put this window control to the side

There is a clip and you need to push it down and make it come right off, after that, put this window control to the side

4-1

4-1

4-2

4-2

4-3

4-3

5. Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray.

Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray

Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray

5-1

5-1

5-2

5-2

6. Next you are going to pull away the trim under the steering wheel.

Next you are going to pull away the trim under the steering wheel

Next you are going to pull away the trim under the steering wheel

6-1

6-1

7. With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set.

With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set

With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set

8. Firmly pull the dash and it should be clipped out.

Firmly pull the dash and it should be clipped out

Firmly pull the dash and it should be clipped out

8-1

8-1

9. With the dash removed, you now can have access to the four bolts that are holding the original car radio.

With the dash removed, you now can have access to the four bolts that are holding the original car radio

With the dash removed, you now can have access to the four bolts that are holding the original car radio

10. Remove these four bolts with the seven millimeter screwdriver.

Remove these four bolts with the seven millimeter screwdriver

Remove these four bolts with the seven millimeter screwdriver

11. With all the bolts removed, the original car radio should simply slide out from the original place.

With all the bolts removed, the original car radio should simply slide out from the original place

With all the bolts removed, the original car radio should simply slide out from the original place

11-1

11-1

12. Disconnect the factory connectors and wires at the back of the original car radio.

Disconnect the factory connectors and wires at the back of the original car radio

Disconnect the factory connectors and wires at the back of the original car radio

13. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

14. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

15. Connect the Seicane car radio to your original radio’s plugs.

16. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane car radio into the dash.

18. Put everything into their original place. All the installation is done.

 

Wish the above installation steps can be helpful for you. If you have any problems, you can contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you are afraid of making damage to either your car radio or your car, you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, it is very essential for you to pick an ideal car radio. If you have no ideas, you can refer to a remarkable 2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio from Seicane. Here comes the link, please click:

https://www.seicane.com/android-2008-2014-2015-2016-2017-jeep-wrangler-bluetooth-gps-radio-car-stereo-with-mirror-link-wifi-steering-wheel-control-plug-and-play-h201

To be honest, this unit can be regarded as one of the best replacements for your factory radio since it is equipped with eight-core CPU, 4G RAM and 32G ROM, and it’s operation system has been upgraded to the most advanced and stable Android 8.0 version.

With the assistance of the worldwide real-time GPS navigation system, this unit enables you to know your current locations and find the right way to reach any locations you would like go to. And thanks to this unit’s dual zone function, you can listen to your favorite music while navigating.

Under the wireless Bluetooth technology, you can connect your Bluetooth-enabled mobile phone to this unit so as to get access to Bluetooth hands-free phone calls as well as Bluetooth streaming music.

As for main features of this car radio, it can support the steering wheel control, headlamp output, reverse output and ACC output. And this unit can support hand brake detecting, the door information display and the original car’s amplifier.

If you like this unit, you can add it to your shopping cart right now. Good luck to you!

2006 2007 2008 2009-2013 Toyota Tundra Car Radio after installation

If you are an owner of 2006 2007 2008 2009-2013 Toyota Tundra, what kind of stereo will you choose to install in your car? As far as I am concerned, a car radio with a wide range of practical and entertainment features can bring you great convenience and enjoyment for your driving. Thus, you can choose such a multifunctional car radio and get it installed in your car. The following is a 2006 2007 2008 2009-2013 Toyota Tundra car radio installation guide from Seicane, which can be taken as your reference if you own the same or similar dashboard.

2006 2007 2008 2009-2013 Toyota Tundra Car Radio after installation

2006 2007 2008 2009-2013 Toyota Tundra Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2006 2007 2008 2009-2013 Toyota Tundra car radio installation guide

1. The original car radio.

The original car radio

The original car radio

2. Pry around the panel on the left of the original car radio with a lever, and release it.

Pry around the panel on the left of the original car radio with a lever, and release it

Pry around the panel on the left of the original car radio with a lever, and release it

3. Remove the bottom pocket with your hands.

Remove the bottom pocket with your hands

Remove the bottom pocket with your hands

4. Remove the air conditioner control with a lever.

Remove the air conditioner control with a lever

Remove the air conditioner control with a lever

5. Remove four mounting screws holding the original car radio in place with a screwdriver as pictures below show.

Remove four mounting screws holding the original car radio in place with a screwdriver as pictures below show

Remove four mounting screws holding the original car radio in place with a screwdriver as pictures below show

5-1

5-1

5-2

5-2

6. Take the original car radio out of the dash with your hands.

Take the original car radio out of the dash with your hands

Take the original car radio out of the dash with your hands

7. Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio

Disconnect all connectors at the back of the original car radio

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original car radio’s plugs.

11. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane stereo into the dash.

13. Put everything into their original place.

 

Wish you can get some help from the above installation guide. If you meet any problems you don’t know how to deal with by yourself, please don’t hesitate to seek help from your dealer, someone experienced or a professional. Or you can directly arrange a professional technician to help you install the new car radio. If you haven’t got an ideal car radio yet, you can refer to an amazing 2006 2007 2008 2009-2013 Toyota Tundra car radio from Seicane.

https://www.seicane.com/android-2006-2013-toyota-tundra-hd-touchscreen-radio-dvd-player-gps-navigation-system-with-steering-wheel-control-bluetooth-wifi-mirror-link-1080p-video-s6927g

This car radio is running on the most advanced Android 8.0 operation system, a high-quality eight-core CPU processor and 4GB RAM as well as 32GB ROM. So with this car radio installed in your car, you can embrace a much smoother, faster and easier operation experience.

Thanks to the text-to-speech guidance provided by the high-end 3D GPS navigation system, you can easily know where you are and have the most suitable route option to reach any locations you would like to go to accurately. And you are able to freely enjoy your favorite music while navigating because of this unit’s dual zone function.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, both Bluetooth hands-free calls and Bluetooth streaming music are both available for you, which can add a lot of convenience and enjoyment to your driving.

If you like this unit, just add it to your shopping cart. Good luck!

2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 car stereo after installation

Do you yearn for upgrading your factory radio with a new multi-functional car stereo on your own? If you would like to have a try, you just need to remove your original car radio and install a new car radio under the correct installation guide. The following is a 2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 car radio installation guide from Seicane. If you have the same or similar dashboard, you can refer to this guide carefully.

2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 car stereo after installation

2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 car stereo after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 Bluetooth GPS Car Stereo Installation Guide

1.The original car radio.

The original car radio

The original car radio

2.Start from the bottom shifter. Remove the shifter and disconnect the connector at the back of it.

Start from the bottom shifter. Remove the shifter and disconnect the connector at the back of it

Start from the bottom shifter. Remove the shifter and disconnect the connector at the back of it

2-1

2-1

3.Remove the center button for the heater control panel.

Remove the center button for the heater control panel

Remove the center button for the heater control panel

3-1

3-1

4.Gently remove the heater control panel.

Gently remove the heater control panel

Gently remove the heater control panel

5.Disconnect the connectors at the back of the heater control panel.

Disconnect the connectors at the back of the heater control panel

Disconnect the connectors at the back of the heater control panel

6.Underneath the original car radio, there are four screws, just remove them so as to take out the original car radio.

Underneath the original car radio, there are four screws, just remove them so as to take out the original car radio

Underneath the original car radio, there are four screws, just remove them so as to take out the original car radio

6-1

6-1

7.Make the new car stereo clip into the original air vent.

Make the new car stereo clip into the original air vent

Make the new car stereo clip into the original air vent

8.Make sure that all connectors and cables are plugged to each other correctly.

Make sure that all connectors and cables are plugged to each other correctly

Make sure that all connectors and cables are plugged to each other correctly

For the further confirmation of the right connecting of all connectors and cables, you can refer to the following wiring diagram.

8-1

8-1

9.Well put the new car stereo into the dashboard.

Well put the new car stereo into the dashboard

Well put the new car stereo into the dashboard

10.Plug the connectors to the heater control panel’s interfaces.

Plug the connectors to the heater control panel's interfaces

Plug the connectors to the heater control panel’s interfaces

11.Place the panel to the original place and fix the screw. And put the shifter back, make sure the connector is connected back as well.

Place the panel to the original place and fix the screw. And put the shifter back, make sure the connector is connected back as well

Place the panel to the original place and fix the screw. And put the shifter back, make sure the connector is connected back as well

11-1

11-1

 

Wish the above installation guide can do some help for you. If you come across any problems, you can seek help from your dealer, communicate with someone experienced or turn to a professional for help. Additionally, if you are afraid of making damage to either your car radio or your car, you can also directly go to a car radio upgrade center and arrange a professional technician to help you install the new car radio. While for the selection of an ideal car radio, if you have no ideas, here I would like to share an amazing 2003 2004 2005 2006 2007 Toyota Corolla E120 BYD F3 car stereo from Seicane with you. For more details, please click:

https://www.seicane.com/android-2000-2007-toyota-corolla-hd-touch-screen-radio-dvd-player-gps-navigation-bluetooth-music-wifi-mirror-link-steering-wheel-control-rearview-camera-1080p-video-s126002e


This amazing car stereo can be regarded as one of the best road companions for you since it comes with both practical and entertainment features.

With the guidance of the high-end 3D GPS navigation system, you are able to easily know your current locations and find the best route t o reach your ideal destinations through turn-by-turn directions and voice prompts. Besides, this unit comes with dual zone function which enables you to listen to your favorite music while navigating.

Additionally, under the wireless Bluetooth technology, you are able to get access to Bluetooth hands-free phone calls and Bluetooth streaming music from your mobile phone as long as you connect your Bluetooth-enabled mobile phone to this unit. Therefore, you can gain both convenience and enjoyment thanks to this car stereo.

Don’t hesitate to take this unit right now if you like it.