Monthly Archives: July 2016

You are browsing the site archives by month.
27Jul 2016

How to skillfully replace a 2006 2007 Mitsubishi Raider head unit with DVD GPS Radio WIFI 1080P Video USB SD Backup camera TV

⋅ Leave a Comment
2006 2007 Mitsubishi Raider after installation

The most up-to-date head unit will make your driving become easier and comfortable. You can reach the destination by the shortest route between two locations with the 3D GPS navigation system. You can make hands-free calls and music streaming with the newest Bluetooth function. A lot of application can be downloaded in the Android Market with the stable android system. If you are worry about the installation, I’d like to teach you how to skillfully replace a 2006 2007 Mitsubishi Raider head unit from Seicane. You can take it as reference and hope it can help you.

2006 2007 Mitsubishi Raider after installation

2006 2007 Mitsubishi Raider after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2006 2007 Mitsubishi Raider head unit installation guide

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2. Take the panel off the dash and disconnect the wires from the car.

2-1.Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2

2-2

3. Use a screw driver to remove the four screws.

Use a screw driver to remove the four screws

Use a screw driver to remove the four screws

4. Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2

4-2

5. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit

Check all the accessories for the new Seicane head unit

6. Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows.

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows

7. Put the new unit into the dash, turn on the new unit and have a test if the new Seicane stereo is working without problem.

8. Put trim panel back on your new Seicane stereo after the normal test.

That’s all the installation guide of the 2006 2007 Mitsubishi Raider head unit and hope it will help you to know more about the head unit. If you don’t have any experience on the installation, it suggest you go to the dealer or professionals to ask for help. Beyond that, the first thing for you to do is find the suitable head unit to install in your car. I have this unit to introduce to you: 2006 2007 Mitsubishi Raider head unit from Seicane.

http://www.seicane.com/seicane-s09206-oem-android-radio-gps-navigation-system-for-2006-2007-mitsubishi-raider-with-canbus-obd2-bluetooth-mirror-link-dvd-player-touch-screen-dvr-backup-camera-tv-steering-wheel-control-wifi-1080p-video-usb-sd

This unique Mitsubishi Raider head unit comes with the most up-to-date android 4.4.4 with fast response and a stable system, support high-definition screen and LVDS input, built in WIFI, 3D GPS Navigation System and so on. You can just insert the SD card to upgrade system, interface, MCU, Bluetooth, Canbus program and etc without no other equipment. To upgrade your car interior and to enjoy a new and different journey, the product is just the right choice!

25Jul 2016

A step-by-step installation guide for 2002 2003 2004-2007 Jeep Wrangler Liberty car stereo with Radio GPS Sat Nav TV Bluetooth Backup Camera

⋅ Leave a Comment
2002 2003 2004-2007 Jeep Wrangler Liberty after installation

It’s time for you to consider replacing it with a brand new car stereo when your factory radio can’t meet your needs anymore. A multifunctional head unit can bring a large great deal of convenience to you. You can drive to your destination without asking the way by the 3D GPS navigation. You can enjoy your favorite music and have fun with your friends or family during driving. I’d like to share the installation guide of 2002 2003 2004-2007 Jeep Wrangler Liberty car stereo from seicane to you.

2002 2003 2004-2007 Jeep Wrangler Liberty after installation

2002 2003 2004-2007 Jeep Wrangler Liberty after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002 2003 2004-2007 Jeep Wrangler Liberty car stereo installation guide

1.Remove the trim panel with a lever.

Remove the trim panel with a lever.

Remove the trim panel with a lever.

2. Remove 4 screws which holds the factory radio in place.

2-1.Remove 4 screws which holds the factory radio in place

2-1.Remove 4 screws which holds the factory radio in place

2-2

2-2

3.Take out the factory radio and disconnect the wires from the car.

3-1.Take out the factory radio and disconnect the wires from the car

3-1.Take out the factory radio and disconnect the wires from the car

3-2

3-2

4. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

5. Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram.

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram

Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram

6. Put the new Seicane head unit into the dash.

7. Install four screws and trim panel.

8. Turn on the new radio and have a comprehensive test if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

That’s all the installation guide for a 2002 2003 2004-2007 Jeep Wrangler Liberty car stereo. Please rest assured that if you find the dashboard is a bit different from yours, the installation guide is quite similar. If you find it hard to install it on your own, it’s suggested you go to the dealer or ask for a professional to have it installed.

In addition, you also need to confirm that your new unit can be compatible with your car. If you are looking for the new one, I’d like to share you the car stereo for 2002 2003 2004-2007 Jeep Wrangler Liberty. You can refer this link to check it:

http://www.seicane.com/cheap-2002-2003-2004-2007-jeep-wrangler-liberty-in-dash-radio-gps-sat-nav-stereo-cd-dvd-player-tv-bluetooth-backup-camera-usb-sd-mp3-mp5-ipod-aux-mp3-t6096

This 2002 2003 2004-2007 Jeep Wrangler Liberty comes with 4.3 inch 800*480 2‐DIN WVGA HD Digital TFT LCD touch screen, bringing sharp image and vivid color. It can support DVD play with auto memory. All the set parameter can be memorized and restored automatically; Adopts cutting-edge electronic shock protection(ESP) technology, being shockproof; Compatible with formats including DVD±R, DVD±RW, CD-R/RW, VCD, HDVD, DVCD, DIVX etc. Don’t be hesitate and

20Jul 2016

A step-by-step installation guide for a 2002 2003 2004 2005 Dodge Neon car radio with MP3 Dual Zone AUX Steering Wheel Control USB SD DVD Bluetooth TV Tuner

⋅ Leave a Comment
2002 2003 2004 2005 Dodge Neon car radio after installation

Nowadays, to buy an ideal car radio is much more affordable for car owners. However, you still need to pay extra money for its installation if you don’t know how to install it. But if you have some related installation experience and a correct guide, you can finish the installation without paying one cent. Please look at the picture which is a multifunctional Seicane 2002 2003 2004 2005 Dodge Neon car radio after installation. If you also have the same dashboard, you can refer to the following detailed instruction.

2002 2003 2004 2005 Dodge Neon car radio after installation

2002 2003 2004 2005 Dodge Neon car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002 2003 2004 2005 Dodge Neon car radio installation steps

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2.Take the panel off the dash and disconnect the wires from the car.

2-1.Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

3.Remove the four screws which are holding the unit with a screwdriver.

3.Remove the four screws which are holding the unit with a screwdriver

Remove the four screws which are holding the unit with a screwdriver

4.Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

5.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio ‘s plugs.

7-1. Connect the Seicane car stereo to your original car radio 's plugs

7-1. Connect the Seicane car stereo to your original car radio ‘s plugs

8.Put the new Seicane car radio into the dash.

9.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10.Put trim panel back on your new Seicane car radio after the normal test.

Now can you install your new radio in you car under the guidance of this detailed installation guide specially for a 2002 2003 2004 2005 Dodge Neon car radio? If not, don’t worry, you can ask a professional for help. If there is any question, you can consult your dealer. But if you don’t have an ideal radio for your car, I’d like to recommend this advanced Dodge Neon car radio from Seicane to you. Here’s the link, please check out the following link for more details:

http://www.seicane.com/car-stereo-radio-gps-navigation-audio-system-for-2002-2007-dodge-intrepid-magnum-neon-with-dvd-bluetooth-tv-tuner-mp3-dual-zone-aux-steering-wheel-control-usb-sd-t6015

This excellent Dodge Neon car radio integrated with a GPS navigation system and a DVD player is compatible with 2002 2003 2004 2005 Dodge Neon right now. You can enjoy an intuitive interface on its large 5 inch multi-touch screen which is with 800*480 pixel resolution. Wish you like this amazing 2002 2003 2004 2005 Dodge Neon car radio and have a great time with it!

19Jul 2016

Easy installation steps for a 2002 2003 2004 CHRYSLER Concorde head unit with Mirror link Touch Screen DVR TV Video WIFI OBD2 Bluetooth USB SD Rearview Camera Quad-core CPU

⋅ Leave a Comment
2002 2003 2004 CHRYSLER Concorde head unit after installation

A correct guide can help you do a lot of things on your own. The installation of a new car stereo is no exception. Now If you are going to replace your factory radio, you can take an instruction for reference. Now I’d like to introduce a detailed 2002 2003 2004 CHRYSLER Concorde head unit installation guide from Seicane to you. Wish it can be helpful for you.

2002 2003 2004 CHRYSLER Concorde head unit after installation

2002 2003 2004 CHRYSLER Concorde head unit after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.Please prepare a lever and a screwdriver before the removal and the installation.

5.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002 2003 2004 CHRYSLER Concorde head unit installation steps

1. Remove the trim piece above cup holder with a lever.

Remove the trim piece above cup holder with a lever

Remove the trim piece above cup holder with a lever

2. Remove 2 screws behind the trim piece.

Remove 2 screws behind the trim piece

Remove 2 screws behind the trim piece

3. Gently pry around the side of trim panel with the lever and then remove the trim panel.

Gently pry around the side of trim panel with the lever and then remove the trim panel

Gently pry around the side of trim panel with the lever and then remove the trim panel

4. Remove 4 screws which holds the factory radio in place.

Remove 4 screws which holds the factory radio in place

Remove 4 screws which holds the factory radio in place

5. Take out the factory radio.

Take out the factory radio

Take out the factory radio

6. Disconnect the smaller harness on the behind of the factory radio.

Disconnect the smaller harness on the behind of the factory radio

Disconnect the smaller harness on the behind of the factory radio

7. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane head unit to your original car radio ‘s plugs.

10. Install four screws and trim panel.

11. Install 2 screws behind the trim piece and the trim piece.

12.Turn on the new radio and have a comprehensive test if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Is it easy for you to understand all the installation steps for a 2002 2003 2004 CHRYSLER Concorde head unit? If not, it’s suggested you consult your dealer. Or you can also directly have a professional install it. If you haven’t found an ideal head unit for your car, you can refer to this amazing 2002 2003 2004 CHRYSLER Concorde head unit from Seicane. It comes with the latest features and capabilities for you to upgrade your factory radio. For more details, you can click:

http://www.seicane.com/seicane-s09201-2002-2003-2004-chrysler-concorde-android-dvd-player-radio-gps-navigation-system-mirror-link-touch-screen-dvr-tv-video-wifi-obd2-bluetooth-usb-sd-rearview-camera-steering-wheel-control

With this CHRYSLER Concorde head unit in your car, video types like DVD/DVD-R/DVD±RW/HDCD/CD-R/CD±RW/MP3/MP4/Picture CD/VCD/WMA are all compatible with this unit, you can play a lot of programs to amuse both yourself and your passengers. The functions of your steering wheel control will still remain after installation. Just upgrade your factory radio with this special CHRYSLER Concorde head unit.

18Jul 2016

How to simply replace a 2002 2003 2004 2005 2006 2007 Jeep Liberty head unit with Bluetooth Music TV IPOD IPhone USB SD MP3 AUX Rearview Camera

⋅ Leave a Comment
2002 2003 2004 2005 2006 2007 Jeep Liberty head unit after installation

Taking a trip in your car with your families is quite pleasant and relaxing, isn’t it? If you are want to keep yourself and your families in your car all the way, it’s a great idea for you to replace your factory radio with a multifunctional head unit. To install a new aftermarket stereo in your car, you can find a correct installation guide to help you. Here I’d like to share a step-by-step 2002 2003 2004 2005 2006 2007 Jeep Liberty head unit from Seicane with you.

2002 2003 2004 2005 2006 2007 Jeep Liberty head unit after installation

2002 2003 2004 2005 2006 2007 Jeep Liberty head unit after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

4.Please prepare a lever and a screwdriver before the removal and the installation.

5. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2002 2003 2004 2005 2006 2007 Jeep Liberty head unit installation steps

1.Loosen the trim panel with a lever.

Loosen the trim panel with a lever

Loosen the trim panel with a lever

2.Take the panel off the dash and disconnect the wires from the car.

2-1.Take the panel off the dash and disconnect the wires from the car

2-1.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

2-2.Take the panel off the dash and disconnect the wires from the car

3.Remove the four screws which are holding the unit with a screwdriver.

Remove the four screws which are holding the unit with a screwdriver

Remove the four screws which are holding the unit with a screwdriver

4.Take out the unit and disconnect the wire harness at the back of the unit.

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-1.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

4-2.Take out the unit and disconnect the wire harness at the back of the unit

5.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane head unit to your original car radio ‘s plugs.

7-1. Connect the Seicane car stereo to your original car radio 's plugs

7-1. Connect the Seicane car stereo to your original car radio ‘s plugs

7-2. Connect the Seicane car stereo to your original car radio 's plugs

7-2. Connect the Seicane car stereo to your original car radio ‘s plugs

8.Put the new Seicane head unit into the dash.

9.Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10.Put trim panel back on your new Seicane head unit after the normal test.

Now can you install your new radio in you car under the guidance of this detailed installation guide specially for a 2002 2003 2004 2005 2006 2007 Jeep Liberty head unit? If not, don’t worry, you can ask a professional for help. If there is any question, you can consult your dealer. But if you don’t have an ideal radio for your car, I’d like to recommend this excellent 2002 2003 2004 2005 2006 2007 Jeep Liberty head unit from Seicane to you. Here’s the link, please check out the following link for more details:

http://www.seicane.com/aftermarket-radio-gps-dvd-player-for-2002-2007-jeep-grand-cherokee-liberty-patriot-wrangler-with-bluetooth-music-tv-ipod-iphone-usb-sd-mp3-aux-rearview-camera-t6015

This modern Jeep Liberty head unit with a remarkable DVD player to support various kinds multimedia playing is your best choice for you to upgrade your original car radio. Its iPod function is desirable for you to plug your iPod or iPhone to listen to your favorite music. You can also charge them at the same time. You can also enjoy many other features for great convenience and enjoyment on the way. Good luck to you!

15Jul 2016

How to upgrade a 1999 2000 2001-2004 Jeep Grand Cherokee head unit with Auto A/V DVD Radio GPS Navigation Bluetooth Music TV Tuner Dual Zone IPOD AUX

⋅ Leave a Comment
1999 2000 2001-2004 Jeep Grand Cherokee head unit after installation

As technology improves, the precision of a GPS navigation has become great. Therefore, almost all the car owners try to install a GPS navigation system in a car. However, some of the factory radio can’t support GPS function. In that case, it’s wise of you to replace your factory radio with a brand new aftermarket head unit. To install a new head unit, you can find a step-by-step installation guide. Wish the following 1999 2000 2001-2004 Jeep Grand Cherokee head unit installation instruction from Seicane can be much helpful for you.

1999 2000 2001-2004 Jeep Grand Cherokee head unit after installation

1999 2000 2001-2004 Jeep Grand Cherokee head unit after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

1999 2000 2001-2004 Jeep Grand Cherokee head unit installation steps

1.Remove the trim piece above cup holder with a lever.

Remove the trim piece above cup holder with a lever

Remove the trim piece above cup holder with a lever

2.Remove 2 screws behind the trim piece.

Remove 2 screws behind the trim piece

Remove 2 screws behind the trim piece

3.Gently pry around the side of trim panel with the lever and then remove the trim panel.

Gently pry around the side of trim panel with the lever and then remove the trim panel

Gently pry around the side of trim panel with the lever and then remove the trim panel

4.Remove 4 screws which holds the factory radio in place.

Remove 4 screws which holds the factory radio in place

Remove 4 screws which holds the factory radio in place

5.Take out the original radio.

Take out the factory radio

Take out the factory radio

6.Disconnect the smaller harness on the behind of the original car radio.

Disconnect the smaller harness on the behind of the factory radio

Disconnect the smaller harness on the behind of the factory radio

7. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9.Connect the Seicane head unit to your original car radio ‘s plugs.

10.Install four screws and trim panel.

11.Install 2 screws behind the trim piece and the trim piece.

12.Turn on the new radio and have a comprehensive test if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

The step-by-step installation guide for a 1999 2000 2001-2004 Jeep Grand Cherokee head unit is shown as the above. Wish you can get some help from it. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this amazing Jeep Grand Cherokee head unit from Seicane. Please click for more details:

http://www.seicane.com/1999-2000-2001-2004-jeep-grand-cherokee-head-unit-auto-a-v-dvd-radio-gps-navigation-bluetooth-music-tv-tuner-steering-wheel-control-dual-zone-ipod-aux-t6096

With this Jeep Grand Cherokee head unit in your car, you can also choose your favorite radio station for global news and instant traffic information with the FM/AM radio. Your steering wheel control can still work after installation. The availability of USB and SD card makes it possible for you to play compatible external devices for more entertainment. Wish you have a great time with it on all trips!

13Jul 2016

How to replace a 2013 2014 Toyota LEVIN car radio with DVD player Bluetooth HD touch screen OBD DVR Rear view camera Mirror link TV USB SD 3G WIFI IPOD

⋅ Leave a Comment
2013 2014 Toyota LEVIN car radio after installation

If you own a 2013 2014 Toyota LEVIN, you may be quite familiar with the picture below. Yes, it’s a head unit from Seicane specially for a 2013 2014 Toyota LEVIN at present. If you also plan to upgrade the capabilities of your factory radio, such a head unit can be a good choice. With it in your car, a lot of convenience and enjoyment can be easily available. Now I’d like to share a step-by-step 2013 2014 Toyota LEVIN car radio installation guide with you. You can take it as a reference for the installation.

2013 2014 Toyota LEVIN car radio after installation

2013 2014 Toyota LEVIN car radio after installation

Some tips before the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2013 2014 Toyota LEVIN car radio installation guide

1.Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2.Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3.Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4.Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6.Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7.If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8.Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane car stereo. Finally the new Seicane car stereo is installed and a comprehensive test should be conducted on the new radio

Wish the detailed installation guide for a 2013 2014 Toyota LEVIN car radio can be helpful for you. For any questions, you can consult your dealer. If you don’t find a suitable stereo for your car, I’d like to recommend this amazing 2013 2014 Toyota LEVIN car radio from Seicane to you, please click for more details:

http://www.seicane.com/16g-quad-core-android-autoradio-gps-navigation-system-for-2013-2014-toyota-levin-with-dvd-player-bluetooth-hd-touch-screen-obd-dvr-rear-view-camera-mirror-link-tv-usb-sd-3g-wifi-ipod-s168014

Take this amazing 2013 2014 Toyota LEVIN car radio in your car, and you can enjoy a lot of new and practical features it brings to you and keep your steering wheel control still working as well. It comes with the most precise GPS navigation system for you to find your way to your desired destination under the guidance of turn-by-turn direction as well as cue voice.

Besides, it is built with a great FM/AM radio for you listen to your favorite station for the latest news and traffic information as well as entertainment in your car. Go and enjoy your driving with this excellent Toyota LEVIN car radio!

12Jul 2016

A detailed installation guide for a 2008-2015 MAZDA 6 car radio with Bluetooth Mirror link GPS multi-touch screen OBD DVR TV USB SD 3G WIFI IPOD Quad-core CPU 16G Flash

⋅ Leave a Comment
2008-2015 MAZDA 6 car radio after installation

How hard is it to install a new head unit in your car? Actually, to install a new head unit just takes several simple steps. Before the installation, you need to easily remove the original car radio. Both of the removal and the installation are simple. Now I’d like to share a step-by-step 2008-2015 MAZDA 6 car radio installation guide from Seicane with you, which can be much helpful during the whole progress.

2008-2015 MAZDA 6 car radio after installation

2008-2015 MAZDA 6 car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2008-2015 MAZDA 6 car radio installation guide

1. Remove your cup holder.

Remove your cup holder

Remove your cup holder

2. Unscrew and remove the shift knob.

Unscrew and remove the shift knob

Unscrew and remove the shift knob

3. Remove the shift trim panel with your fingers.

Remove the shift trim panel with your fingers

Remove the shift trim panel with your fingers

4. Then remove both sides trim panel of the speed control.

Then remove both sides trim panel of the speed control

Then remove both sides trim panel of the speed control

5. Pull out the panel and set it aside.

Pull out the panel and set it aside

Pull out the panel and set it aside

6. Remove four screws on each side of the speed control with a Phillips-screwdriver.

Remove four screws on each side of the speed control with a Phillips-screwdriver

Remove four screws on each side of the speed control with a Phillips-screwdriver

7.Pull out the speed control slowly.

Pull out the speed control slowly

Pull out the speed control slowly

8. Find two screws under the radio and remove them.

Find two screws under the radio and remove them

Find two screws under the radio and remove them

9. Push the top panel and set it aside.

Push the top panel and set it aside

Push the top panel and set it aside

10. Remove two screws with a Phillips-screwdriver as the picture shows.

Remove two screws with a Phillips-screwdriver as the picture shows

Remove two screws with a Phillips-screwdriver as the picture shows

11. Pull out the factory radio slowly.

Pull out the factory radio slowly

Pull out the factory radio slowly

12. Disconnect the original harness and set the factory radio aside.

Disconnect the original harness and set the factory radio aside

Disconnect the original harness and set the factory radio aside

13. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

14. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

15. Connect the Seicane car radio to your original car radio ‘s plugs.

16. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane radio into the dash.

18. Put everything into their original place. All the installation is done.

The step-by-step 2008-2015 MAZDA 6 car radio installation guide is shown as the above. Wish you can get some help from it. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this modern 2008-2015 MAZDA 6 car radio from Seicane. Please click for more details:

http://www.seicane.com/android-car-dvd-player-radio-navigation-system-for-2008-2015-mazda-6-with-bluetooth-mirror-link-gps-multi-touch-screen-obd-dvr-rearview-camera-tv-usb-sd-3g-wifi-ipod-s168001

This top 2008-2015 MAZDA 6 car radio is of great utility to support Bluetooth connectivity, DVD and music playing, FM/AM radio tuner, RDS, iPod function, USB and SD card connection, etc. With special wiring harness, you can easily install this plug-and-play unit in your car without modifying or cutting any wire. Built in a remarkable

GPS navigation system, it can smoothly and promptly lead you to your desired destination with the intelligent route planning, 3D street view, landmark display, turn-by-turn direction as well as voice prompts it provides for you. Wish you like this remarkable 2008-2015 MAZDA 6 car radio and have great time with it!

11Jul 2016

How to easily upgrade a 2007-2015 Mazda CX-9 car stereo with DVD player Android 5.1.1 GPS navigation system Bluetooth HD touch screen Mirror link OBD DVR USB SD

⋅ Leave a Comment
2007-2015 Mazda CX-9 car stereo after installation

Does your factory radio come with the GPS navigation function? If not, it’s wise of you to replace your factory radio with a multifunctional head unit which can support a lot of features. In that way, you can easily get to your desired destination under the correct guidance of the GPS function. The installation of a new aftermarket car radio is quite easy. Here comes a step-by-step 2007-2015 Mazda CX-9 car stereo installation guide from Seicane for your reference.

2007-2015 Mazda CX-9 car stereo after installation

2007-2015 Mazda CX-9 car stereo after installation

Tips about the installation: 

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2007-2015 Mazda CX-9 car stereo installation guide

1. Pry on both sides panels of the radio.

Pry on both sides panels of the radio

Pry on both sides panels of the radio

2. Open the cup holder and pry on the shifter panel, pull it out slowly. Watch out the wiring behind it.

Open the cup holder and pry on the shifter panel, pull it out slowly. Watch out the wiring behind it

Open the cup holder and pry on the shifter panel, pull it out slowly. Watch out the wiring behind it

3. Remove the screw with the Phillips-head screwdriver.

Remove the screw with the Phillips-head screwdriver

Remove the screw with the Phillips-head screwdriver

4. Pull out the panel under the radio and disconnect the wiring behind it.

Pull out the panel under the radio and disconnect the wiring behind it

Pull out the panel under the radio and disconnect the wiring behind it

5. Remove two screws on the both sides of the radio.

5. Remove two screws on the both sides of the radio

5. Remove two screws on the both sides of the radio

6. Pull out the dash cover on the radio slowly and unplug the wiring behind the dash cover.

6. Pull out the dash cover on the radio slowly and unplug the wiring behind the dash cover

Pull out the dash cover on the radio slowly and unplug the wiring behind the dash cover

7. Remove the four screws on either side of the Mazda’s stereo bracket with the Phillips-head screwdriver.

Remove the four screws on either side of the Mazda’s stereo bracket with the Phillips-head screwdriver

Remove the four screws on either side of the Mazda’s stereo bracket with the Phillips-head screwdriver

8. Take out the original radio and disconnect the original harness.

Take out the original radio and disconnect the original harness

Take out the original radio and disconnect the original harness

9. Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio

Disconnect all connectors at the back of the original car radio

10. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

11. Connect the harnesses to the back of the new Seicane car stereo.

12. Connect the Seicane car stereo to your original car radio ‘s plugs.

13. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane stereo into the dash.

15. Put everything into their original place.

Wish the 2007-2015 Mazda CX-9 car stereo installation above can be helpful you. If you have any question, it’s suggested you turn to your dealer for help. If you don’t have any experience on the installation, you’d better have it installed by a professional. Besides, you need to confirm your new stereo can be suitable for your car. To check the compatibility, you are welcome to click the link below which is about a top 2007-2015 Mazda CX-9 car stereo from Seicane.

http://www.seicane.com/2007-2015-mazda-cx-9-radio-dvd-player-android-gps-navigation-system-with-bluetooth-hd-touch-screen-mirror-link-obd-dvr-usb-sd-3g-wifi-rear-view-camera-tv-ipod-quad-core-cpu-16g-flash

This top 2007-2015 Mazda CX-9 car stereo can greatly enhance the capabilities in a car with advanced configurations and the great utility. It also comes with a large 8 inch 1024*600 digital high definition TFT LCD touch screen to facilitate the operation as well as the viewing.

The availability of Bluetooth enables you to pair your mobile phone with this unit, and the phonebook function allows you to directly search for contact number and call out by touching the big screen. To have great fun on the way, this intelligent Mazda CX-9 car stereo is just your best choice!

08Jul 2016

How to easily upgrade a 2010 Ford Transit Connect car radio with GPS navigation system Capacitive multi-touch screen OBD DVR Bluetooth TV 3G WIFI USB SD Mirror link Quad-core CPU 16G Flash

⋅ Leave a Comment
2010 Ford Transit Connect car radio after installation

Can your factory radio bring much convenience and excitement for you, for example, GPS navigation? If not, then it’s wise of you to upgrade it with a new aftermarket car radio. If you have a 2010 Ford Transit Connect and are looking for a detailed car radio installation guide to install your new radio, you can take this 2010 Ford Transit Connect car radio installation guide for reference before and during the installation.

2010 Ford Transit Connect car radio after installation

2010 Ford Transit Connect car radio after installation

Please notice before the installation:    

1.Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.

2.A lever and a screwdriver need to be prepared before the installation.

3.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2010 Ford Transit Connect car radio installation guide

1. Remove the panel with a lever.

Remove the panel with a lever

Remove the panel with a lever

2. Unscrew four screws holding the original radio with a screwdriver.

Unscrew four screws holding the original radio with a screwdriver

Unscrew four screws holding the original radio with a screwdriver

3. Gently take the original car radio out of the dashboard.

Gently take the original car radio out of the dashboard

Gently take the original car radio out of the dashboard

4. Disconnect all connectors at the back of the original car radio.

5. Check all the accessories for the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the Seicane car radio to your original car radio 's plugs

Connect the Seicane car radio to your original car radio ‘s plugs

7. Connect the Seicane car radio to your original car radio ‘s plugs.

8. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane radio into the dash.

10. Put everything into their original place.

Wish the detailed installation guide for a 2010 Ford Transit Connect car radio can be helpful for you. If your dashboard is different from that shown in the guide above, please don’t worry, the installation is similar, and it won’t have much influence on the whole. For any questions, you can consult your dealer.

On the other hand, if you don’t find a suitable stereo for your car, I’d like to recommend this amazing 2010 Ford Transit Connect car radio from Seicane to you, please click for more details:

http://www.seicane.com/android-2010-ford-transit-connect-gps-radio-dvd-player-with-gps-navigation-system-capacitive-multi-touch-screen-obd-dvr-bluetooth-rear-view-camera-tv-3g-wifi-usb-sd-mirror-link-s167017

This remarkable 2010 Ford Transit Connect car radio with a number of features and high configurations is your best choice to upgrade your factory radio. You can enjoy your favorite music when you are navigating to your destination. Besides, you are able to pair your compatible mobile phone via the Bluetooth connectivity, so that you can keep your hands on the steering wheel and stay focused on the road ahead to make and receive phone calls as well as stream music.