How hard is it to install a new head unit in your car? Actually, to install a new head unit just takes several simple steps. Before the installation, you need to easily remove the original car radio. Both of the removal and the installation are simple. Now I’d like to share a step-by-step 2008-2015 MAZDA 6 car radio installation guide from Seicane with you, which can be much helpful during the whole progress.
2008-2015 MAZDA 6 car radio after installation
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400
2008-2015 MAZDA 6 car radio installation guide
1. Remove your cup holder.
Remove your cup holder
2. Unscrew and remove the shift knob.
Unscrew and remove the shift knob
3. Remove the shift trim panel with your fingers.
Remove the shift trim panel with your fingers
4. Then remove both sides trim panel of the speed control.
Then remove both sides trim panel of the speed control
5. Pull out the panel and set it aside.
Pull out the panel and set it aside
6. Remove four screws on each side of the speed control with a Phillips-screwdriver.
Remove four screws on each side of the speed control with a Phillips-screwdriver
7.Pull out the speed control slowly.
Pull out the speed control slowly
8. Find two screws under the radio and remove them.
Find two screws under the radio and remove them
9. Push the top panel and set it aside.
Push the top panel and set it aside
10. Remove two screws with a Phillips-screwdriver as the picture shows.
Remove two screws with a Phillips-screwdriver as the picture shows
11. Pull out the factory radio slowly.
Pull out the factory radio slowly
12. Disconnect the original harness and set the factory radio aside.
Disconnect the original harness and set the factory radio aside
13. Check all the accessories for the new Seicane car radio.
Check all the accessories for the new Seicane car radio
14. Connect the harnesses to the back of the new Seicane car radio.
Connect the harnesses to the back of the new Seicane car radio
15. Connect the Seicane car radio to your original car radio ‘s plugs.
16. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
17. Put the new Seicane radio into the dash.
18. Put everything into their original place. All the installation is done.
The step-by-step 2008-2015 MAZDA 6 car radio installation guide is shown as the above. Wish you can get some help from it. If there is any question, you can consult your dealer. However, if you can’t finish it on your own, you’d better ask a professional for help. If you are still looking for an ideal car stereo for your car, you can refer to this modern 2008-2015 MAZDA 6 car radio from Seicane. Please click for more details:
This top 2008-2015 MAZDA 6 car radio is of great utility to support Bluetooth connectivity, DVD and music playing, FM/AM radio tuner, RDS, iPod function, USB and SD card connection, etc. With special wiring harness, you can easily install this plug-and-play unit in your car without modifying or cutting any wire. Built in a remarkable
GPS navigation system, it can smoothly and promptly lead you to your desired destination with the intelligent route planning, 3D street view, landmark display, turn-by-turn direction as well as voice prompts it provides for you. Wish you like this remarkable 2008-2015 MAZDA 6 car radio and have great time with it!
Recent Comments