Author Archives: Jeen

new car stereo DVD GPS navigation system of 2014 Jeep Grand Cherokee

new car stereo DVD GPS navigation system of 2014 Jeep Grand Cherokee

This is the new car stereo DVD GPS navigation system of 2014 Jeep Grand Cherokee.You will know whether this stereo can be installed in

your car by comparing their trim panels between this unit and original one.

 

Do you have a car of Jeep Grand Cherokee for 2008-2011?If your answer is yes and you want to upgrade its sound system,then you can patiently read

this article that will show you 2014 Jeep Grand Cherokee  DVD GPS

with BT Ipod music installation.

 

Many people update car audios is just like we are changing our cell phones very rapidly.If

you have no time to do it yourself,a professional person can do this only if you pay him

corresponding fees.And is it possible to do by yourself?

 

It’s a fact that a lot of drivers have demonstrate they can succeed installing

Jeep Grand Cherokee DVD GPS system.It doesn’t need technical skills but right removal

tools,and you should be gentle when you are prying parts of the unit and keep well them.

 

Some precautions before installation:

1.Have a check for your car series include the radio to see whether everything is ok and then

turn off them and park your car well

2.Please disconnect negative cable before you begin to work,this will ensure you more safer

3.You’d better make enough preparation for your installation work by searching enough

information about this unit,and next website may help you a lot:http://www.seicane.com/o

em-gps-navigation-stereo-remove-for-2008-2009-2010-2011-jeep-grand-cherokee-with-am

-fm-radio-rds-bluetooth-tv-tuner-cd-dvd-player-hd-1080p-c202

4.Preparing tools which will be used in the process

 

2014 Jeep Grand Cherokee stereo removal and  dvd GPS installation:

1.Use a pry tool to prize lower control buttons to remove it

Use a pry tool to prize lower control buttons to remove it

Use a pry tool to prize lower control buttons to remove it

2.Make cables behind it unplugged,you can use a tool help you if it is very tight,remove

button controls and put it aside

Make cables behind it unplugged

Make cables behind it unplugged

3.Makie off 2 screws ,which has one on each side

Makie off 2 screws ,which has one on each side

Makie off 2 screws ,which has one on each side

4.Gently lever edges around trim panel to release and remove it

Gently lever edges around trim panel to release and remove it

Gently lever edges around trim panel to release and remove it

5.Remove 4 screws beside the stereo,there are two on each side

Remove 4 screws beside the stereo,there are two on each side

Remove 4 screws beside the stereo,there are two on each side

6.Remove factory stereo and disconnect cables back of it

Remove factory stereo and disconnect cables back of it

Remove factory stereo and disconnect cables back of it

These 6 steps are about how to remove original car stereo and next we will learn

Jeep Grand Cherokee new audio system installation.It can normally divided into

3 steps.

 

1.Making cables connection:this affair may be the most difficult thing for most people

for things containing wires is always more complex than other things.So you should be

very serious to do it.You can read the installation instructions within your new stereo

carefully and do the connection step by step.

2.After that,install new stereo in your car and turn on your radio to see whether your

installation is correct

3.If everything is ok,then make other removed parts back on car,including screws

and trim panel

Precautions after installation:

1.Please do not be too excited after successful installation,remember that keeping you

safe can only enjoy more entertainments,so do not stare at it when you are driving

2.Please do not use any chemicals to wash it,neither other kind of cleaning products

3.When you are driving on a rainy day,you should pay more attention to the touch screen

of head unit,for moisture may gather on it and cause damage to the machine

4.Please change the exhausted batteries in time in order to make your upgraded radio

can be used longer

 

 

Head unit after installation,aftermarket DVD GPS navigation system of DODGE RAM 1500 2500 3500

Head unit after installation,aftermarket DVD GPS navigation system of DODGE RAM 1500 2500 3500

This is the head unit after installation,aftermarket DVD GPS navigation system of DODGE RAM

1500 2500 3500.

 

It doesn’t fit cars with navigation at present,so if your DODGE RAM 1500 2500 3500’s stereo

has no navigation,it means that it can be installed in your car.And except these cars,it also fits

some other cars,including 2008 2009 2010 Jeep Commander,2009 2010 2011 Jeep Compass,

2008-2014 Jeep Grand Cherokee,2007 2008 2009 2010 Jeep Wrangler Unlimited.

 

Nowadays more and more people are upgrading their car stereos in order to enjoy more

comfortable life when they are driving. The same to DODGE RAM owners,now the problem

we will solve is knowing the 2009 2010 2011 DODGE RAM 1500 2500 3500 navigation

system installation.

 

Aftermarket car stereo is surely more advanced than factory one,and have some difference in

a lot of places,such as appearance and functions.If you have no experience of operating it,then

figure these out by visiting some websites or watching videos,and here is a video which may be

a not bad choice:

 

2009 2010 2011 DODGE RAM 1500 2500 3500 original stereo removal:

1.Original audio system of DODGE RAM

Original audio system of DODGE RAM

Original audio system of DODGE RAM

2.Pry and release trim panel with the help of  a lever

Pry and release trim panel with the help of  a lever

Pry and release trim panel with the help of a lever

3.Disconnect cables behind the unit before you can remove trim panel totally

Disconnect cables behind the unit before you can remove trim panel totally

Disconnect cables behind the unit before you can remove trim panel totally

4.Use a screwdriver and remove 4 screws,each side has two

Use a screwdriver and remove 4 screws

Use a screwdriver and remove 4 screws

5.Gently remove factory CD player and disconnect cables at the back of it

Gently remove factory CD player and disconnect cables at the back of it

Gently remove factory CD player and disconnect cables at the back of it

2009 2010 2011 DODGE RAM navigation system installation:

6.Connect wires include all antennas and cables step by step as following pictures show

About this work,I suggest you to check your connection after you have finished it,for it’s

a key part but easy make something wrong,thus you should be very careful with this

Connect antennas,cables and connectors

Connect antennas,cables and connectors

Connect antennas,cables and connectors 2

Connect antennas,cables and connectors 2

Connect antennas,cables and connectors 3

Connect antennas,cables and connectors 3

7.After that,install the new unit in the car,you’d better have a tidy  for wires before that

install the new unit in the car,you’d better have a tidy  for wires before that

install the new unit in the car,you’d better have a tidy for wires before that

Turn on your radio and if it works well,fix 4 screws beside the installed radio to firm the unit,

and install other objects back to right places.This is total process for DODGE RAM navigation

system installation.You may get more detailed information about this unit from this link:http://www.seicane.com/car-cd-radio-stereo-sound-upgrade-for-2009-2010-2011-dodge

-ram-pickup-trucks-ram-1500-2500-3500-with-3d-gps-dvd-bluetooth-tv-3g-wifi-aux-c202.

 

You should notice things that is emphasized in this article,because they are points that

people are easy to do something wrong or cause damage to car even to people.

 

Some precautions after installation:

1.You should pay more attention on your head unit if you are driving on a abnormal day,for example,rainy day,for moisture may gather on it and probably arouse damage to it

2.If you have used your radio to watch videos for a long time and you find its temperature is

very high,then you’d better turn it off to let it have a rest

3.In order to make your car stereo can used longer,please do not use any chemical products

to wipe it,neither other detergents,if needed you can use a cloth that is clean and dry

 

Here is a picture of new unit after installation,audio stereo navigation system of 2005 2006

2007 Chrysler 300C.You can have a careful look at it if you are interested in installing the

aftermarket Chrysler 300C navigation system.

 

New unit after installation,audio stereo navigation system of 2005 2006 2007 Chrysler 300C

New unit after installation,audio stereo navigation system of 2005 2006 2007 Chrysler 300C

 

No matter whether it fits your car,you can continue reading this article ,because removal and

installation procedure for car stereo is similar in most parts.So you can learn something that

is useful anyway from here.

 

If you are one owner of Chrysler 300C,let’s talk about how to install 2005 2006 2007 Chrysler

 300C navigation system with radio DVD BT.

 

And before you decide to operate it,you can have a look at the following video first,it may help you have a more clear image about  this new audio:

 

 

2005 2006 2007 Chrysler 300C original radio removal and nav system installation:

1.Stretch your hand in this space which is under control buttons

Stretch your hand in this space which is under control buttons

Stretch your hand in this space which is under control buttons

2.Remove a panel in that space,disconnect its cables

Remove a panel in that space,disconnect its cables

Remove a panel in that space,disconnect its cables

3.Use your hand to loosen the big trim panel around it,then remove it

Use your hand to loosen the big trim panel around it,then remove it

Use your hand to loosen the big trim panel around it,then remove it

4.Disconnect antennas and cables behind it

Disconnect antennas and cables behind it

Disconnect antennas and cables behind it

5.Remove four screws,which has 2 on each side of the CD radio

Remove four screws,which has 2 on each side of the CD radio

Remove four screws,which has 2 on each side of the CD radio

6.Then you can take out the factory stereoand unplug antennas at back of it

Then you can take out the factory stereoand unplug antennas at back of it

Then you can take out the factory stereoand unplug antennas at back of it

Removal affairs has been finished,after all connectors are disconnected from factory stereo,the wires should be done like the picture show:

Sort wires after removal

Sort wires after removal

The next work is to install new stereo into the car,actually it can be easier than front operations

except cables connection.What you should do is mainly two things:connect antennas and

connectors correctly and install new audio in its right position.And you need to pay more attention

on connection by reading installation instructions carefully,or you can ask a professional person to

help you.After this,install new unit in its right space.

 

Then make four screws back to the radio,and cover trim panels on the surface.With all these done,

you can turn on your new unit and check all functions to see whether you have succeed

accomplishing it.

 

Please do not be too eager to use the new machine,for you are not familiar with it and may do

something wrong.Therefore you need to know enough things about its functions,the following

website may be a not bad choice: http://www.seicane.com/in-dash-chrysler-300c-multimedia

-dvd-player-gps-3d-navigation-audio-system-with-bluetooth-radio-tv-usb-sd-3g-wifi-c206.

 

It will make your driving life more advanced and convenient,it fits needs of people.For example,

the gps navigation system is very popular among most drivers.It’s really convenient for you when

are on a busy driving,such as you are talking on the phone or when you are arriving in a strange

place,the 3D GPS system will help you by showing a map on the screen.

 

When you see next radio which is specially for 2011 2012 2013 Opel Astra, you may feel confused for there is

some difference between this one and original one of car on appearance and functions.

Head unit after installation,gps dvd with sat nav bluetooth music of 2011 2012 2013 Opel Astra

Head unit after installation,gps dvd with sat nav bluetooth music of 2011 2012 2013 Opel Astra

 

Factory one’s screen is only used for showing something,while this one’s screen is

touch screen that you can also operate on it with your hand or touch screen pen. A

lot of people have the idea to install a dvd gps for his Opel Astra to catch up with

society trend and enjoy themselves better during driving at the same time.And this

is same to aim of this article,because you will see detailed steps on how to install

2011 2012 2013 Opel Astra dvd GPS system support Bluetooth iPod Rearview

today.

 

Before you begin radio installation,you need to mind a series of things to make

your work more smooth.

 

Precautions about installation:

1.Please remember to turn off your radio and other equipment,and make negative

battery cable

disconnected to avoid unnecessary damage to people

2.In addition,when you are doing removal affairs,please place original CD player

and removed screws in safe places to ensure that you can find needed things after

you have installed unit in at later time

 

Next we will talk about how to remove factory radio and install Opel Astra DVD GPS system.It’s usual for you to find some difference between your car radio

appearance with the following one,don’t worry and you can take it as reference

because stereos for a series of cars are substantially uniform.

 

2011 2012 2013 Opel Astra original radio removal:

1.Take out all things in this space

Take out all things in this space

Take out all things in this space

2.Pry surface file panel and remove it with a pry tool,take this screw and the

other corresponding

one out then you can remove it absolutely

Pry surface file panel and remove it

Pry surface file panel and remove it

take this screw and the other corresponding one out

take this screw and the other corresponding one out

3.Loosen big around trim panel and remove it

Loosen big around trim panel and remove it

Loosen big around trim panel and remove it

4.Open 2 small trim panels and take out 2 screws and other 2 under them

Open 2 small trim panels and take out 2 screws and other 2 under them

Open 2 small trim panels and take out 2 screws and other 2 under them

5.Make out lower notch and make cables disconnected at the back of it

Make out lower notch

Make out lower notch

make cables disconnected

make cables disconnected

6.Gently remove factory stereo and unplug cables behind it,some cables

may be very tight and you can do it with a pry tool

Gently remove factory stereo and unplug cables behind it

Gently remove factory stereo and unplug cables behind it

7.Pry around edges of upper control buttons on the panel and remove it

Pry around edges of upper control buttons on the panel and remove it

Pry around edges of upper control buttons on the panel and remove it

2011 2012 2013 Opel Astra DVD GPS installation:

8.Install it on new trim panel,and same to lower control button

Install it on new trim panel

Install it on new trim panel

9.Make connection on cables and connectors,which is shown in following

picture

Make connection on cables and connectors

Make connection on cables and connectors

Make connection on cables and connectors2

Make connection on cables and connectors2

Make connection on cables and connectors3

Make connection on cables and connectors3

Make connection on cables and connectors4

Make connection on cables and connectors4

10.After finishing cables connection,install new unit into the right place

and reinstall that big trim panel and other panels to the car

install new unit into the right place

install new unit into the right place

 

11.After above work has been done, turn on your new radio and check

if it’s installed right and whether functions can operate

 

If you need to know more information about new radio, I suggest you

to make enough preparations for both installation and the unit,you’d

better seek some information from the Internet,for example:

http://www.seicane.com/oem-aftermarket-car-radio-upgrade-sat

-navi-system-for-opel-astra-with-fm-am-3g-wifi-3-zone-pop-built

-in-gps-dvd-bluetooth-ipod-rearview-c072, which will help you get a lot

of detailed messages include images,module and so on.

 

In fact this kind of installation is a little more complex than other ones on

connecting cables,but I haveconfidence that most of you will make it clear

with the help of above 12 specific steps and clear images.

 

If your beloved car belongs to 2010 2011 Renault Megane,we hope that most system of it can

be corresponding well advanced.This is a normal psychology and today I will show you

detailed and easy installation steps for 2010 2011 Renault Megane navigation audio

system with BT music AUX-in to help you achieve audio part of the car.

A lot of people are updating their car stereos to enjoy more entertaining life,and it’s

achieved by driving car with a multimedia dvd diaplay.Compared with factory stereo,a new

radio has increased new functions in it to make our driving time more enjoyable and make

us feel easy,I think this is one object of its production.

The aftermarket radio stereo for Renault Megane is different from some other autoradios,for

its touch screen is placed farther than normal ones with occluders surround it.You needn’t

to worry that it’s not convenient for you to watch the screen,however it can not only let you

see clearer on shinning days,but also protect your screen from damage or collision,which will

surely length its lifetime.This is an advantage and if you have doubts here is a picture to help

you get a intuitive feeling:DVD gps navigation system bluetooth of 2010 2011 Renault

Megane.

DVD gps navigation system bluetooth of 2010 2011 Renault Megane

DVD gps navigation system bluetooth of 2010 2011 Renault Megane

 

It’s not enough to you to make well understanding of Renault Megane navigation system with

this picture,,then I advice you to seek for more messages about it from the Internet,for example:

http://www.seicane.com/in-dash-car-dvd-radio-player-specialized-for-renault-megane-with-gps-navigation-ready-built-in-3g-wifi-bluetooth-rear-view-camera-3d-map-c145.

 

2010 2011 Renault Megane car stereo removal and installation:

1.Pry the trim above the glove box off

Pry the trim above the glove box off

Pry the trim above the glove box off

2.Reveal these 3 torx screws

Reveal these 3 torx screws

Reveal these 3 torx screws

3.Pry the trim off the unit

Pry the trim off the unit

Pry the trim off the unit

4.Remove the screw which is on drivers side

Remove the screw which is on drivers side

Remove the screw which is on drivers side

5.Pry the steering wheel off surround to gain access to more torx screws

Pry the steering wheel off surround to gain access to more torx screws

Pry the steering wheel off surround to gain access to more torx screws

6.Nothing with these two screws

Nothing with these two screws

Nothing with these two screws

7.Pry the pillar trim off

Pry the pillar trim off

Pry the pillar trim off

8.Remove the 2 torx screws which are at each corner of the dash,then pull the outer part of

the rivet out

Remove the 2 torx screws which are at each corner of the dash

Remove the 2 torx screws which are at each corner of the dash

9.Carefully make the dash out off the middle

Carefully make the dash out off the middle

Carefully make the dash out off the middle

10.Lift the dash back

Lift the dash back

Lift the dash back

11.Carefully make the dash out of the car over the steering wheel and store it safely

Carefully make the dash out of the car over the steering wheel and store it safely

Carefully make the dash out of the car over the steering wheel and store it safely

12.Press down on the tabs at each side of the unit and then pull it backwards

Press down on the tabs at each side of the unit and then pull it backwards

Press down on the tabs at each side of the unit and then pull it backwards

13.Disconnect the connectors at the back

Disconnect the connectors at the back

Disconnect the connectors at the back

You may think it a little complex to accomplish removal procedure,but won’t only if you can

act according to them,and your work is not over yet for you will continue to install  a new

one in your car.

You should read carefully about cables connecting part from installation instructions and act

it according to right guide step by step,After right connection,install new unit into your car.

Turn on new unit and have a check for it.If all function operates well,then firm all removed

screws back to original places and the same to other removed parts.Then whole procedure

is finished.

Please be careful when you are installing the new unit,and you’d better ask one of your friends

beside to help you.Be gentle to your car equipment and be serious when doing every step.

If you want to know more stereos for some other cars,you can find them on some websites,for

example:http://www.seicane.com/.

 

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander.

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander

Upgrading car stereos can be a self-done thing in recent years,because there are a lot of materials on the Internet which can help you achieve this goal.

So if you are a owner of 2006-2011 Mitsubishi outlander,installing a dvd player with navigation system for your car by yourself is also very possible to realize when you have known easy installation steps for 2006-2011 Mitsubishi outlander navigation system support Mp3 Mp4.

Before you upgrade car audio system,you need to make adequate preparations for this process.Such as reading some essaies,watching videos,visiting some websites and so on.And you need to make these preparations including preparing removal tools after you have made it very clear.

Another question that you have no idea is that whether the aftermarket Mitsubishi outlander navigation system fits your car,here is a method for you:have a careful look at its trim panel and see if it’s same with your factory one’s.

2006-2011 Mitsubishi outlander car stereo removal and installation:

1.Open up the glove compartment

Open up glove compartment

Open up glove compartment

2.Get out screw to side panel,then remove side panel

Get out screw to side panel

Get out screw to side panel

3.Gently drag trim piece toward seat place

remove side panel by pulling toward seat

remove side panel by pulling toward seat

5.Use panel removal tool,gently pry edges around stereo face

use your hand or panel removal tool,gently pry around edges of stereo face

use your hand or panel removal tool,gently pry around edges of stereo face

6.Disconnect this cable,and do not start your car at that time

Disconnect the connector

Disconnect the connector

7.Get four screws holding stereo in place out

Make out four screws holding stereo in place

Make out four screws holding stereo in place

8.Get out stereo for access to harnesses behind it

Get out stereo for access to harnesses behind it

Get out stereo for access to harnesses behind it

9.Get out smaller connector to give access to Grom Y-harness, plug Grom harness into open port, connect removed harness to Grom Y-harness, Make 20-pin harness connected to Grom unit

Get out smaller connector to give access to Grom Y-harness

Get out smaller connector to give access to Grom Y-harness

plug Grom harness into open port

plug Grom harness into open port

connect removed harness to Grom Y-harness

connect removed harness to Grom Y-harness

Make 20-pin harness connected to Grom unit

Make 20-pin harness connected to Grom unit

10.Use provided P-Tap to make connection,please have a check that if P-Tap has punctured wire and is tightly secured

Use provided P-Tap to make connection

Use provided P-Tap to make connection

11.Plug stripped wire in as far as possible as the picture show

Plug stripped wire in as far as possible as the picture show

Plug stripped wire in as far as possible as the picture show

12.Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

13.After finishing cables connection,turn on new stereo and check new unit and hope that you can enjoy a good time with new audio system

I guess most of you are not very clear about operations for this dvd,you can visit next website for more detailed usful knowledge: http://www.seicane.com/digital-touch-screen-car-dvd-player-gps-navigation-specialized-for-2006-2011-mitsubishi-outlander-with-radio-bluetooth-usb-sd-3g-wifi-c056.

If you are also interested in the installation affairs about Mitsubishi L200 navigation,you can go to and have a look at it.

 

 

 

 

Do you have the experience of installing car radio dvd player for 2010 2011 Mazda 3?Maybe you will think that there is no need to do by yourself,all things for installation can be accomplished by professional technicians.

Do you have the experience of installing car radio dvd player for 2010 2011 Mazda 3?Maybe you will think that there is no need to do by yourself,all things for installation can be accomplished by professional technicians.

However,it’s possible to achieve it yourself when you know how to install 2010 2011 Mazda 3 navigation dvd with AUX-in USB SD.But to avoid any damage or danger,please do not do self-installation or maintain to the unit privately.

If you have made up your mind to do it yourself,you can do it under the condition that you have made clear Mazda 3 navigation dvd installation,and you’d better ask someone else beside you to give you a hand and you can have a discussion with him or her.

This is how the aftermarket dvd GPS navigation system of 2010 2011 Mazda 3 looks like.

Aftermarket dvd GPS navigation system of 2010 2011 Mazda 3

Aftermarket dvd GPS navigation system of 2010 2011 Mazda 3

Before installation,you can start the radio to check whether your audio system is normal;whether the inside and outside part of car have any unusual phenomenon.If everything works well,then you can begin your action.Next is the main content I will show you.

2010 2011 Mazda 3 original cd radio removal and new dvd radio installation:

1.Use panel removal tool (a plastic scraper) to pry and take air vent out to avoid damaging the plastic

Use panel removal tool (a plastic scraper) to pry and take air vent out

Use panel removal tool (a plastic scraper) to pry and take air vent out

2.Put air vent in front place and then remove two screws that used to fix the radio

Put air vent in front place

Put air vent in front place

remove two screws that used to fix the radio

remove two screws that used to fix the radio

3.Slip one finger into each side behind the panel,then remove the radio

Slip one finger into each side behind the panel

Slip one finger into each side behind the panel

remove the radio

remove the radio

4.Use a special tool as the picture show to disconnect the grey antenna

Use a special tool as the picture show to disconnect the grey antenna

Use a special tool as the picture show to disconnect the grey antenna

5.Disconnect the stock AUX input connector

Disconnect the stock AUX input connector

Disconnect the stock AUX input connector

6.Flip the stock stereo over thus you can see the locking tab on the main antennas,then make the main connector unplugged

flip the stock radio over and make the main connector disconnected

flip the stock radio over and make the main connector disconnected

7.Here is the empty stereo bay which is just for your new unit

the empty stereo bay which is just for your new unit

the empty stereo bay which is just for your new unit

8.Make the eonon wiring harness connected one by one:aux input cable,canbus adapter,antenna adapter,main connector

aux input cable

aux input cable

canbus adapter

canbus adapter

antenna adapter

antenna adapter

main connector

main connector

9.GPS antenna installattion:this position is just under the dash behind vents to get better signals and does not require any visible wiring

Position for GPS antenna does not require any visible wiring

Position for GPS antenna does not require any visible wiring

10.Make DVD lock-down screws out

Make DVD lock-down screws out

Make DVD lock-down screws out

11.USB and Ipod/Ipad cables:one of them is located in the glove compartment,one 3/4” hole will allow all other three wires to pass;use a 3/4” wood-boring bit,and carefully practice so the drill does not go through any farther than necessary

the glove compartment

the glove compartment

12.Insert the USB connector from the radio side,insert the Ipod antenna from the glove compartment and then comes to final connections and fit

13.Connect remaining cables:

GPS and WIFI antenna(gold)

IPod/iPad cable(black)

Aux L/R(red/white)

Main Harness(black)

Connect remaining cables

Connect remaining cables

14.Sort the cables well and slip the radio into position

Sort the cables well

Sort the cables well

Put the radio into its space carefully

Put the radio into its space carefully

15.Connect the WIFI antenna to the left of the GPS antenna,in front of the instrument cluster.Route the wires thus they come down between the two ventilation openings as the picture show.Extra cables may be cliled,tied,and stowed deeper into the cavity behind the vents

sort cables as the picture show

sort cables as the picture show

16.Re-connect battery cable of the unit to make it works.Turn on new radio,check the steering wheel buttons as well

Re-connect battery cable of the unit

Re-connect battery cable of the unit

 

check the steering wheel buttons

check the steering wheel buttons

17.Screw the two screws  beside the radio

Screw the two screws  beside the radio

Screw the two screws beside the radio

18.At last,check if all wires are still in place,and re-install other  panel to the car

re-install other  panel to the car

re-install other panel to the car

19.New audio stereo after installation, gps navigation bluetooth with 3G Wifi of 2010 2011 Mazda 3

New audio stereo after installation, gps navigation bluetooth with 3G Wifi of 2010 2011 Mazda 3

New audio stereo after installation, gps navigation bluetooth with 3G Wifi of 2010 2011 Mazda 3

 

Whole installation procedure is accomplished,it seems to be complex but you can do it well only if you are patient and careful to do it according to correct instructions.

If you need to know more detailed information about the unit,then visiting corresponding websites is not a bad choice,for example: http://www.seicane.com/8-inch-in-car-gps-navigation-stereo-replacement-for-2010-2011-mazda-3-with-3d-map-cd-dvd-player-bluetooth-music-mp3-tv-tuner-3g-wifi-aux-1080p-dvr-pop-hd-video-c034.

 

Precautions after installation:

1.You can use a clean soft fabric clean the radio ,but no strong chemicals,cleaning agents,or strong detergent,or it will cause damage to it

2.Please don’t use other sharp objects but your finger or touch screen pen if you have to operate the stereo,otherwise your machine may can’t work properly

 

 

 

Car stereo after installation,gps nav system with bluetooth music of 2011 2012 KIA K2

Car stereo after installation,gps nav system with bluetooth music of 2011 2012 KIA K2

Maybe you can recognize the unit in above image because you went to shopping in car market and saw it before.You may need to install a new one at that time,but you are not clear which one to choose or don’t know how to install 2011 2012 KIA K2 GPS radio car stereo sound system.

Then don’t worry,for I will try to help you solve this problem.A stereo as the picture show is one specially for 2011 2012 KIA K2,because the trim panel of it is same to factory one’s.And you know that one car can install not only one dvd,and one dvd can also be installed in some cars.

Nowadays most cars have corresponding car stereos that fit each one,and principles of removal and installation are generally same.Whatever whether this unit is suitable for your car,you can also have a patient look at following installation instructions for KIA K2 GPS system that will benefit you a lot.

Here are 2 tips for you before I show you removal steps in order to avoid unnecessary damage or any danger to car or even people.Don’t be afraid,it’s ok in normal cases.

Precautions before installation:

Please make sure that you have finished all parking series and turn off your radio before you start up any work;To ensure security please remember to disconnect the negative battery cable

2011 2012 KIA K2 original radio removal and GPS radio installation:

1.Factory dashboard of KIA K2

Factory dashboard of KIA K2

Factory dashboard of KIA K2

2.Use a lever to pry upper trim panel,and you can use your hand to pry it after it is fastened

Use a lever to pry upper trim panel

Use a lever to pry upper trim panel

you can use your hand to pry it after it is fastened

you can use your hand to pry it after it is fastened

3.After all parts are fastened,you can remove it totally

Remove trim panel totally

Remove trim panel totally

4.Use a pry tool to lever dashboard around and then remove it by disconnecting cable

Use a pry tool to lever dashboard around

Use a pry tool to lever dashboard around

remove it by disconnecting cable

remove it by disconnecting cable

5.Remove four screws that fixed the radio with a screwdriver

Remove four screws that fixed the radio

Remove four screws that fixed the radio

6.Then you can get out radio easily and disconnect cables at back of it

get out radio

get out radio

disconnect cables at back of it

disconnect cables at back of it

7.Make connection between new radio’s cables and car’s

Make connection between new radio's cables and car's

Make connection between new radio’s cables and car’s

8.Release this prat of rubber as the picture show

Release this prat of rubber

Release this prat of rubber

9.Get down screws that lay on two sides and use a knife to pry lower place of it

Get down screws that lay on two sides

Get down screws that lay on two sides

use a knife to pry lower place of it

use a knife to pry lower place of it

10.Put cables in the space after those two steel are taken out

Put cables in the space after those two steel are taken out

Put cables in the space after those two steel are taken out

11.Connect cables between new dvd and car system,fix screws back to it,then put it well in

Connect cables between new dvd and car system

Connect cables between new dvd and car system

fix screws back to it

fix screws back to it

12.Install trim panel back to your car

Install trim panel back to your car

Install trim panel back to your car

After general read for above 12 specific steps and operate according it,you can turn on your installed dvd player and check whether your installation is all right.

For more specific information,you can visit some related websites,for example: http://www.seicane.com/7-inch-2011-2012-kia-k2-touch-screen-gps-dvd-player-auto-a-v-radio-rds-bluetooth-music-wifi-rearview-camera-aux-dvr-steering-wheel-control-ipod-hd-1080p-c106 . If you meet some tricky problems that you have no experience,you’d better ask a professional man to help you deal with them.

Precautions after installation:

1.Please do not use strong chemicals or detergent wash the machine,if you need to make a tidy,you can use a clean and dried cloth

2.You can use your hand or the touch screen pen to operate new radio, without using other sharp objects, or it will cause damage to screen

3.Please keep well the removed things for usage again during later process

 

As one of the owners of Hyundai Verna for 2010 2011 2012 2013,what do you think of removing original CD player of it and upgrade a more advanced one?

Many people choose it just to catch up with trend,however,it will also bring us more entertaining and convenient life.And this article will show you how to remove and install 2010 2011 2012 2013 Hyundai Verna head unit with GPS system radio bluetooth function.

Here is an image of new unit after upgrade,car head unit stereo navigation system of 2010 2011 2012 2013 Hyundai Verna.This is an aftermarket radio which is suitable for the car,it’s specially produced for Hyundai Verna,thus trim panels of original one’s and this one’s are same.

new unit after upgrade,car head unit stereo navigation system of 2010 2011 2012 2013 Hyundai Verna

new unit after upgrade,car head unit stereo navigation system of 2010 2011 2012 2013 Hyundai Verna

If you decide to remove and install the head unit by yourself,you can ask a professional person for help who can make a judgement on whether you did is correct or wrong.You can act like this,and it’s also all right if you do it yourself with precise installation guide.In that case,you should do as following installation guide show,and make much preparations for it.You can visit some websites to get more detailed useful information,for example:http://www.seicane.com/2-din-dvd-gps-head-unit-mount-for-2010-2011-2012-2013-hyundai-verna-with-3d-navigation-bluetooth-music-tv-tuner-am-fm-radio-dvr-pop-ipod-iphone-hd-1080p-video-backup-camera-aux-c067.And prepared some tools which may be needed in the process,include a screwdriver, a lever and so on.

2010 2011 2012 2013 Hyundai Verna head unit removal and installation:

1.Prize the lower part of the dashboard with a soft pry tool

Prize the lower part of the dashboard with a soft pry tool

Prize the lower part of the dashboard with a soft pry tool

2.Gently remove the dashboard and disconnect the cable

Gently remove the dashboard and disconnect the cable

Gently remove the dashboard and disconnect the cable

3.Remove these four screws with a screwdriver

Remove these four screws

Remove these four screws

4.After that,you can gently make out the CD player and disconnect the cables back of it

gently make out the CD player

gently make out the CD player

disconnect the cables back of it

disconnect the cables back of it

5.Sort out wires well,pry the plastic panel away from CD radio with a lever

Sort out wires well

Sort out wires well

pry the plastic panel away from CD radio with a lever

pry the plastic panel away from CD radio with a lever

6.Remove these four screws as the picture show

Remove these four screws as the picture show

Remove these four screws as the picture show

7.Install the new head unit into car and fix the screws on it

Install the new head unit into car

Install the new head unit into car

fix the screws on it

fix the screws on it

8.Connect all cables between the new radio and car and do it carefully

Connect all cables between the new radio and car and do it carefully

Connect all cables between the new radio and car and do it carefully

Before you install Hyundai Verna head unit,you’d better read the installation instructions carefully first to make clear how the wires should be connected.Then make connections step by step as it shows.If you are not very sure about it,then check the connection again before you mount new unit into the car.

I guess thetime when you are driving a car with upgraded car head unit must be very entertaining,especially when you are on a free journey with your family or friends.We can enjoy good time by listening to music,watching HD videos,searching Internet and so on.

The 3D GPS navigation system is very helpful for people who are lazy to remember roads or not good at recognizing roads.What’s more,when you are in a strange place,and you are hardly find right direction,don’t worry,your new stereo unit can draw an intelligible map on the screen,you can see it directly.

Precautions after installation:

Your car will possibly enter heat protection mode if your car head unit with GPS BT is operated abnormally,such as runs with very fast speed for a long time,or meet the situation when temperature is over 70 degrees.At this kind of case,you should pay more attention to it.

I have another essay which is about Hyundai I30 navigation dvd installation,if you are interested it,you can have a look at it,there are also many other cars’ stereo installation there.

 

Firstly,we can have a look at this picture:it’s head unit after installation,aftermarket audio navigation system of 2008 2009 2010 2011 Toyota Auris.

head unit after installation,aftermarket audio navigation system of 2008 2009 2010 2011 Toyota Auris

head unit after installation,aftermarket audio navigation system of 2008 2009 2010 2011 Toyota Auris

Are you the owner of Toyota Auris from 2008 to 2011 and is your car stereo looks like this one?Maybe most of you haven’t upgraded it for taking it as a complex thing.But actually it’s not if you can find right and detailed installation steps for 2008 2009 2010 2011 Toyota Auris navigation system with bluetooth dvd.

From the picture at the beginning,we can find that this new unit is different from original ones on its outside appearance and functions.Many people choose to replace original stereo with a new one just for these changes.With high speed development of technology,people can also enjoy its labor work very quickly.

If you are not very familiar with this unit and have a lot of questions,I advice you to visit following website which has detailed information for it:http://www.seicane.com/double-din-sat-nav-speaker-upgrade-for-2008-2009-2010-2011-toyota-auris-with-hd-touch-screen-radio-rds-cd-dvd-player-tv-tuner-3g-wifi-aux-ipod-steering-wheel-control-c028.

Searching information about car dvd installation include reading essays which will show you specific steps to achieve it,so it’s right for you to have a look at it,no matter what kind of situation you are in,it will benefit your life more or less.

There are about 7 steps to achieve the process of Toyota Auris navigation installation,and this process is mainly on the removal steps.Because if you finished removal affairs it means that you have finished most of the installation.Removal affairs generally can be divided into four parts,including remove trim panel,loose screws,remove dashboard the CD player.

2008 2009 2010 2011 Toyota Auris car stereo removal and navigation installation:

1.Unclip side panels from higher center console with the help of panel removal tool

Unclip side panels from higher center console with the help of panel removal tool

Unclip side panels from higher center console with the help of panel removal tool

If you feel a little hard,you can open up the left beside console to achieve this

open up the left beside console

open up the left beside console

2.Take down four screws which parted two on each side where the consoles were removed

Take down four screws which parted two on each side

Take down four screws which parted two on each side

3.You can remove the dashboard gently but also easily after four screws are taken down

remove the dashboard gently

remove the dashboard gently

4.Then take the original CD player out

take the original CD player out

take the original CD player out

5.Disconnect all the cables one by one

Disconnect all the cables one by one

Disconnect all the cables one by one

6.Connect all cables between new unit and those of the car, install it into right place

7.Put the dashboard inand firm screws which were put aside

It won’t take you too much time to accomplish the installation procedure.Please be gentle to those things that are removed by you,such as panels and you also set the screws at a visible place for easy to find.

I believe that your life especially when you are on a journey with car will be more colorful when it has a such car dvd player,and the gps nav system is one of the most popular functions.But before you enjoyed all these,keep your safety in mind when you are upgrading your car radio.

Warm tips:

Multi-functions of new head unit are good indeed,but do not let them instead of your attention or vigor,or it can be very dangerous.

You can enjoy the beautiful music or listen to radio tuner when you are busy driving.

For more car stereos,you can visit http://www.seicane.com/ to have a better choice.