Category Archives: Car Dvd Honda

Actually, getting my first car is a little hard, so I cherish it very much and keep it maintained regularly. It’s a 2009 Honda Civic (LHD), since I purchased it, I used it for work, picking up children to and from school, as well as road trips. For us, the car is one of the important family member.

The Honda Civic has been with us for 7 years, there were more or less breakdown in some parts, but we got them repaired in time to avoid inconvenience. Besides, to enrich in-car life, especially during road trips, we also upgraded some parts of the car, and last month, we just replaced the factory radio for a new one to ready for our coming summer trip. Below is the replacement guide.

Car radio replacement instructions for 2006-2011 Honda Civic (LHD)

I purchased the new aftermarket radio system from Seicane and finished the replacement job with my kids, hoping to enhance their interest in DIY. Before the installation job, make sure you have tools like plastic pry tool, screwdriver in hand and cut off the car power for safety. This picture shows the original radio.

原车图

Step 1 Use the plastic pry tool to pry the small board under the radio system, and remove the two eight millimeter bolts of the plastic trim.

s1

Step 2 Carefully pull out the panel under the steering wheel.

s2

Step 3 Remove the screws that fixed the whole top panel, then pull out the whole top panel and unplug its connector.

s3

Step 4 Pull out the original radio unit and unplug all the connectors.

s4

Step 5 Check the cable accessories of the new Seicane car radio GPS system.

s5

Step 6 Remove the HVAC control board, air outlet and related accessories of the old radio panel, and install them to the new car navigation radio.

s6

Step 7 Remove these white and black small chips of the original head unit, then install them on the new radio unit.

s7

Step 8 Correspondingly connect cables between new car radio navigation system and the car.

s8

Step 9 Turn on the car to test whether the new car radio unit functions normally.

s9

Step 10 If there is no problem, fix the new radio in the dashboard, and install all the panel accessories in their original positions.

安装效果图

Comparison of Seicane car radio navigation system and factory radio

As you can see the first picture, the factory radio is the old-fashioned and button-operated radio which only has simple functions. It can’t meet our continually increasing needs in entertainment and driving safety. For example, with such a factory radio, how can we make hand-free Bluetooth calls? Where to display navigation? And how to reverse easily since there is no reversing images to see? While the Seicane car radio helps us more than these.

Firstly, with the 10.1 inch HD resolution touchscreen, we get a large and comfortable vision when operate the Seicane navigation radio system. The high configuration such as intelligent pure Android 10.0 operation system, 8-core CPU etc. keep a fast and smooth operation and stable performance. In terms of entertainment, this radio gives you the ability to get the latest albums of your favorite singers and watch various interesting videos online.

In fact, the primary reason we want to upgrade the factory radio is to get navigation and reversing assist. Now with this amazing Seicane car radio system, we arrive to destination quickly and have no trouble to reverse.

If you are planning to upgrade your Honda Civic (LHD) radio, give a try for Seicane.

111

2014 2015 Honda FIT car stereo after installation

To take your factory radio up a notch, there are more and more options for you to choose from as the technology improves. Some of them are with exquisite appearance, some are with multiple features, while some are with the most competitive price. You can easily pick an ideal one according to your own needs. Here I’ d like to share a detailed installation guide about a Seicane 2014 2015 Honda FIT car stereo, you can follow it to help with your installation.

2014 2015 Honda FIT car stereo after installation

2014 2015 Honda FIT car stereo after installation

 

 

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

 

 

2014 2015 Honda FIT car stereo installation guide

1·Remove the original console panel with a lever, pry gently along the gap and pick up the panel. Then set it aside.

1. Remove the original console panel with a plastic knife

1. Remove the original console panel with a plastic knife

 

2·Remove the four screws that fixed the radio on the dashboard. Removing these screws will not be a difficult job.

2. Remove the four screws that fixed the radio on the dashboard

2. Remove the four screws that fixed the radio on the dashboard

 

3·Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

3. Pull the factory radio out of the dash

3. Pull the factory radio out of the dash

 

4·Unplug the connectors.

4. Unplug the connectors

4. Unplug the connectors

 

5·Remove the brackets on both sides of the factory radio. So far the removal of the factory radio is completed. Next steps will move on to the installation of the Seicane radio.

5. Remove the brackets on both sides of the factory radio

5. Remove the brackets on both sides of the factory radio

 

6·Install the brackets on both sides of the Seicane radio.

 

7·Dock the connectors of the original vehicle and the upgraded car audio.

7. Dock the connectors of the original vehicle and the upgraded car stereo

7. Dock the connectors of the original vehicle and the upgraded car stereo

 

8·Insert the wires to the appropriate location of the upgraded head radio. If you are not sure about how to wire correctly, you may refer to the wiring diagram for details.

 

9·Fix the Seicane stereo with the four screws.

9. Fix the Seicane stereo with the four screws

9. Fix the Seicane stereo with the four screws

 

10·Firm the console panel. Finally the new Seicane stereo is installed and a comprehensive test should be conducted on the new stereo.

Firm the console panel

10. Firm the console panel

10. Firm the console panel

 

Above all, it’s not too difficult to install a new stereo in your car. Please makes sure you are clear about every step before the installation. If you lack of experience to finish the installation on your own, you’d better have it install by a professional. Besides, you need to find a suitable stereo for your car. If you don’t have one, I’d like to recommend a great 2014 2015 Honda FIT car stereo from Seicane to you, please click:

 

http://www.seicane.com/10-2-inch-oem-android-radio-capacitive-touch-screen-for-2014-2015-honda-fit-support-3g-wifi-bluetooth-gps-navigation-system-tpms-dvr-obd-ii-aux-headrest-monitor-control-video-rear-camera-usb-sd-s083690

 

This intelligent Honda FIT car stereo is an ideal replacement for you to upgrade your factory radio. A number of practical features, such as bluetooth hands-free calls, bluetooth music, GPS navigation system, DVD player, Ipod, FM/AM radio, Wifi, etc. are all made for you to get the convenience and entertainment in your vehicle. To make your parking easier, you can also connect a backup camera for help.

 

Just take your great trips with this amazing Honda FIT car stereo with you all the way. Good luck to you!

 

2012 2013 2014 Honda CRV car stereo after installation

Here is an intelligent 2012 2013 2014 Honda CRV car stereo after installation from Seicane. It looks so pretty, doesn’t it?

2012 2013 2014 Honda CRV car stereo after installation

2012 2013 2014 Honda CRV car stereo after installation

 

 

A new car radio can not only guide you to your desired destination with the most accurate direction but also offer a huge ton of fun for you to relax on the way. To install a new car radio may be difficult for some car owners. However, if you have some related installation experience and a detailed installation guide, you may find that it’s not so much difficult. Here is a step-by-step installation guide for you as a reference.

 

Some tips before the installation:

  1. Please disconnect the power before the installation.
  2. Please prepare a lever and a screwdriver before the removal and the installation.
  3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

 

 

2012 2013 2014 Honda CRV car stereo installation guide

1.Pry the below left control button with a screwdriver and then pry the right one.

2012 2013 2014 Honda CRV car stereo installation step 1

2012 2013 2014 Honda CRV car stereo installation step 1

 

2.Softly take out the panel.

2012 2013 2014 Honda CRV car stereo installation step 2

2012 2013 2014 Honda CRV car stereo installation step 2

 

3.Use a screwdriver remove two screws which lay in left and right sides of the top panel,and keep screws well for use again.

2012 2013 2014 Honda CRV car stereo installation step 3

2012 2013 2014 Honda CRV car stereo installation step 3

 

4.Prize the front of dashboard with a lever, after it was fastened remove it.

2012 2013 2014 Honda CRV car stereo installation step 4

2012 2013 2014 Honda CRV car stereo installation step 4

 

5.Remove this upper dashboard gently,you may still use screwdriver to help you.

2012 2013 2014 Honda CRV car stereo installation step 5

2012 2013 2014 Honda CRV car stereo installation step 5

 

6.Take out two screws which lay in left and right sides of downward place.

2012 2013 2014 Honda CRV car stereo installation step 6

2012 2013 2014 Honda CRV car stereo installation step 6

 

7.After these work,you can gently get the CD player out.

2012 2013 2014 Honda CRV car stereo installation step 7

2012 2013 2014 Honda CRV car stereo installation step 7

 

8.Plug all the cables which connected them.

2012 2013 2014 Honda CRV car stereo installation step 8

2012 2013 2014 Honda CRV car stereo installation step 8

 

9.Plug cables of the new Seicane stereo to car wires and firm the four screws to their original places.

  1. Check whether the new Seicane stereo is working without problem.

 

Hopefully you can get some help from the above guide for a 2012 2013 2014 Honda CRV car stereo. If you find it too hard to finish it on your own, please go to a car stereo upgrade center to have it installed. Besides, it’s necessary for you to make sure you have a right stereo for you car. If you have no idea about this, please check:

 

http://www.seicane.com/10-2-inch-aftermarket-android-touch-screen-gps-navigation-system-for-2012-2013-2014-honda-crv-support-bluetooth-radio-tpms-dvr-obd-ii-rear-camera-aux-headrest-monitor-control-usb-sd-hd-1080p-video-3g-wifi-s083688

 

This Seicane Honda CRV car stereo comes with a region-free DVD disk player enables you to play any DVD from every country in the world. A number of entertainment options can also be available to relax via the USB and SD card connection. The worldwide real-time GPS makes it easier for you to find your way to any location with turn-by-turn direction and spoken guidance. You can make hands-free calls and stream music by simply connecting with your enabled mobile phone via bluetooth technology.

 

Go and enjoy your great trips with this popular Seicane Honda CRV car stereo as your perfect road companion. Good luck to you!

Here comes an attractive Seicane Honda CR-V head unit after installation. It can be easily installed in a 2006-2011 Honda CR-V without any gap. The great convenience and enjoyment it brings to you will must satisfy you.

 

2006-2011 Honda CR-V head unit after installation

2006-2011 Honda CR-V head unit after installation

 

If you want to have a more comfortable car life and a relaxing driving experience, it’s wise of you to upgrade your factory radio with a modern aftermarket head unit with a lot of features which can meet all your needs in a car. Some car owners may worry about the installation of a new head unit, in fact, the installation is quite simple. With some related experience and a correct installation guide, you can easily install a head unit on your own. If you have a same or similar dashboard with the above picture, you can refer to the following detailed Honda CR-V head unit installation instructions.

 

Precautions:

  1. Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.
  2. A lever and a screwdriver need to be prepared before the installation.

 

2006-2011 Honda CR-V head unit installation guide

  1. The original radio of the car.
2006-2011 Honda CR-V head unit installation step 1

2006-2011 Honda CR-V head unit installation step 1

 

2. Use a screwdriver to push up the heater control on the right side. Do the same on the left side.

2006-2011 Honda CR-V head unit installation step 2

2006-2011 Honda CR-V head unit installation step 2

 

  1. Take out the heater control with your hands.
2006-2011 Honda CR-V head unit installation step 3

2006-2011 Honda CR-V head unit installation step 3

 

4.Pry the top of the decoration panel with removal tools and remove it with your hands, and put it aside.

2006-2011 Honda CR-V head unit installation step 4-1

2006-2011 Honda CR-V head unit installation step 4-1

2006-2011 Honda CR-V head unit installation step 4-2

2006-2011 Honda CR-V head unit installation step 4-2

 

5.Push out the vent panel with your hands at the back and set it on the top of the dashboard.

2006-2011 Honda CR-V head unit installation step 5-1

2006-2011 Honda CR-V head unit installation step 5-1

2006-2011 Honda CR-V head unit installation step 5-2

2006-2011 Honda CR-V head unit installation step 5-2

 

6.Remove four screws(two on the top, the other two at the bottom) holding the radio in the dash.

2006-2011 Honda CR-V head unit installation step 6

2006-2011 Honda CR-V head unit installation step 6

 

  1. Take the original radio out of the dash with your hands.
2006-2011 Honda CR-V head unit installation step 7

2006-2011 Honda CR-V head unit installation step 7

 

8.Unplug the connectors at the back of the original radio.

2006-2011 Honda CR-V head unit installation step 8

2006-2011 Honda CR-V head unit installation step 8

 

  1. Make antennas and cables of the new Seicane head unit connected step by step as installation instructions show, and you should be very careful when you are doing this for it will affect the whole procedure.
  2. Put the new Seicane head unit into the dash.
  3. Turn on the new Seicane head unit and check whether the unit is working properly.
  4. Install screws and the panel, and put everything into their original place.

 

If you find the above steps are difficult for you, it’s suggested you go to a car stereo upgrade center to install it or ask a professional technician to help you. Wish it can be helpful for you if you are going to do it on your own.

 

To make sure you have a successful upgrading, it’s essential you have a specific head unit which is suitable to your car. Because different head units are made for different cars. If you have no idea which head unit can fit your car, I’d like to share an intelligent Honda CR-V head unit from Seicane to you, which can be seamlessly installed in your car, please click:

 

http://www.seicane.com/seicane-s1276898-8-inch-quad-core-2006-2011-honda-cr-v-android-4-4-4-dvd-navigation-car-stereo-with-3g-wifi-radio-rds-bluetooth-mirror-link-obd2-16g-flash-rearview-camera-steering-wheel-control-hd-1080p-video-mp3

 

This remarkable Honda CR-V head unit comes with a wide range of features, such as a DVD player and a radio integrated with a GPS system and Bluetooth. The GPS can provide you with the real-time guidance to help you find your way easily. The Bluetooth technology allows you to easily sync your mobile phone for hands-free conversations and streaming music. You can also utilize the USB/iPod connection to play whatever you like.

 

Upgrade your factory radio with this amazing Honda CR-V head unit right now and enjoy all your trips in the future.

All kinds of information are upgrading with a rapid speed nowadays, the traffic information is no exception. Therefore, it’s essential for you to have a precise GPS navigation system to guide you to find your way to your destination. During a long trip, you must want to have something to relax in your car, in that case, a powerful multimedia player is helpful. Look at the following unit, it’s a multifunctional Honda Civic car stereo with GPS navigation function and a DVD player after installation specially made for 2006-2011 Honda Civic.

2006-2011 Honda Civic car stereo after installation

2006-2011 Honda Civic car stereo after installation

 

If you have a Honda Civic from 2006 to 2011 and have the exactly same or similar dashboard with the above picture, you can refer to the following Honda Civic car stereo installation instruction to help with your installation.

 

Precautions:

  1. Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.
  2. A lever and a screwdriver need to be prepared before the installation.

 

2006-2011 Honda Civic car stereo installation guide

  1. The original CD player.

    2006-2011 Honda Civic car stereo installation step 1

    2006-2011 Honda Civic car stereo installation step 1

 

2. Pry the cover of the slot below the CD player with a lever and remove it.

2006-2011 Honda Civic car stereo installation step 2

2006-2011 Honda Civic car stereo installation step 2

 

  1. Remove two screws inside the slot with a ninety-degree screwdriver.
2006-2011 Honda Civic car stereo installation step 3

2006-2011 Honda Civic car stereo installation step 3

 

4.Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel.

2006-2011 Honda Civic car stereo installation step 4

2006-2011 Honda Civic car stereo installation step 4

 

  1. Remove one screw in the dash.
2006-2011 Honda Civic car stereo installation step 5

2006-2011 Honda Civic car stereo installation step 5

 

6.Remove the vent panel.

2006-2011 Honda Civic car stereo installation step 6

2006-2011 Honda Civic car stereo installation step 6

 

  1. Unplug the connectors beneath the panel.
2006-2011 Honda Civic car stereo installation step 7

2006-2011 Honda Civic car stereo installation step 7

 

8.Pry the edges along the panel of the original radio, then remove it, after that, take the original CD player out of the dash.

2006-2011 Honda Civic car stereo installation step 8

2006-2011 Honda Civic car stereo installation step 8

 

  1. Unplug the connectors at the back of the original radio.
2006-2011 Honda Civic car stereo installation step 9-1

2006-2011 Honda Civic car stereo installation step 9-1

2006-2011 Honda Civic car stereo installation step 9-2

2006-2011 Honda Civic car stereo installation step 9-2

 

  1. Disconnect the antenna and the other connector on the other side of the original radio.
2006-2011 Honda Civic car stereo installation step 10-1

2006-2011 Honda Civic car stereo installation step 10-1

2006-2011 Honda Civic car stereo installation step 10-2

2006-2011 Honda Civic car stereo installation step 10-2

 

11.Make antennas and cables of the new Seicane car stereo connected step by step as installation instructions show, and you should be very careful when you are doing this for it will affect the whole procedure.

  1. Put the new Seicane car stereo into the dash.
  2. Turn on the new Seicane car stereo and check whether the unit is working properly.
  3. Install the panel and screws, and put everything into their original place.

 

If you find the dashboard in the above installation guide is different from yours, please don’t worry, the installation is similar, it won’t have much impact on the installation. If you think all the steps are too hard for you to understand or operate, you’d better ask a professional to help you or directly go to a car stereo upgrade center to have it installed.

 

A suitable car stereo for your car is quite important if you want to have a satisfying upgrade. If you don’t know which car stereo can fit your car, I’d like to share a great Honda Civic car stereo with you, please click:

 

http://www.seicane.com/seicane-s127658l-16g-android-4-4-4-autoradio-navigation-aftermarket-stereo-for-2006-2011-honda-civic-with-quad-core-cpu-3g-wifi-dvd-radio-rds-bluetooth-mirror-link-obd2-steering-wheel-control-quad-core-cpu-aux

 

This modern Honda Civic car stereo comes with an advanced Android 4.4.4 operating system and a powerful RK3188 1.6 GHz Cortex A9 Quad-core processor to smooth the operation. With the GPS system, you won’t get lost even you are in an unfamiliar place. To pair your mobile phone which has Bluetooth with this unit, you can make and receive calls without taking your hands off the steering wheel control as well as enjoy your favorite music while you are driving.

 

Under a big discount right now, it’s time to get this Honda Civic car stereo and install it in your car. Wish you will enjoy your new car stereo and have a good time with it.

Nowadays, Honda CRV is more and more popular, and it’s a good choice for most of us. Some of you might be owners of it. The original radio of Honda CRV has few functions, the wisdom choice is remove it and install a new aftermarket Honda CRV Radio with many useful functions. Here are some instructions for you.

This is the Seicane radio after installation of 2012 2013 2014 Honda CRV.

2012 2013 2014 Honda CRV Radio after installation

2012 2013 2014 Honda CRV Radio after installation

2013 Honda CRV radio removal

1)Connect a memory saver unit to your CRV according to the manufacturer’s instructions. Open the hood. Loosen the negative battery cable terminal, using a battery wrench. Disconnect the negative battery cable from the battery.

2) Find the five hidden retainers that hold each vent to the dashboard(one in each upper corner, one on each side and one at the lower point). Pry between the vent and the dash at the aforementioned points to disengage the retainers. Remove the vents from the dashboard.

2012 2013 2014 Honda CRV radio removal step 1

2012 2013 2014 Honda CRV radio removal step 1

3) Remove the two bolts that secure the radio and bracket assembly to the dashboard.

2012 2013 2014 Honda CRV radio removal step 2

2012 2013 2014 Honda CRV radio removal step 2

4) Pull the unit out slowly.

2012 2013 2014 Honda CRV radio removal step 3

2012 2013 2014 Honda CRV radio removal step 3

5) Disconnect the wiring harnesses from the rear of the radio.

2013 Honda CRV radio installation

1)Before connecting,please make sure the ignition is off to avoid short circuit.

2)Make antennas and cables connected step by step as installation instructions show,and you should be very careful when you are doing this for it will affect whole procedure.

3)Connected the new aftermarket radio to Honda CRV, I’d like to advice you checking your connections are correct,the new unit is in right position,and you’d better have a tidy for the cables.

4)If everything is OK, make trim panel back on your new unit.

Safety notes:

  1. Before connecting,please make sure the ignition is off to avoid short circuit.
  2. Ensure connect the yellow and red power cable at last.
  3. Ensure that all loose wires are isolated with electrical tape
  4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
  5. Ensure that all ground is connected to the same place.
  6. Using the improper fuse may cause damage of fire,so when replace the fuse, please consult the professional.

 

By the way, do you have a good aftermarket radio for your Honda CVR? If you haven’t bought it, I’d like to share a good aftermarket Honda CVR Radio with you:

http://www.seicane.com/10-2-inch-aftermarket-android-touch-screen-gps-navigation-system-for-2012-2013-2014-honda-crv-support-bluetooth-radio-tpms-dvr-obd-ii-rear-camera-aux-headrest-monitor-control-usb-sd-hd-1080p-video-3g-wifi-s083688

 

Featuring with a number of up-to-date capabilities for you to upgrade your factory radio, this GPS navigation system for 2012 2013 2014 Honda CRV is the best replacement for you. This car stereo with an Android 4.2 operation system and a 1.6GHz Cortex A9 Dual Core CPU has a smooth and stable performance. Its 10.2 inch LCD digital capacitive multi-touch screen is desirable for you to operate and view everything. A journey filled with safety and enjoyment is possible for you when you simply pair your enabled mobile phone with this unit to make and receive hands-free calls and music streaming. This Honda CRV Radio is plug and play and the installation is quite easy.