Category Archives: Car Dvd Mitsubishi

Mitsubishi Universal car stereo after installation

Here comes an attractive 2012+ Mitsubishi Universal car stereo from Seicane. It looks quite pretty, doesn’t it?

Mitsubishi Universal car stereo after installation

Mitsubishi Universal car stereo after installation

 

 

Some car owners may think it’ s impossible for them to install a stereo on their own. Actually, more and more car owners have demonstrated successful installation on their own at home. With some related installation experience, you can also do it under the help of a detailed installation guide. If you also have the same dashboard as above, the following instructions can be helpful for you.

 

Some tips before the installation:

  1. Please disconnect the power before the installation.
  2. Please prepare a lever and a screwdriver before the removal and the installation.
  3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

 

 

Mitsubishi Universal car stereo installation guide

1·Remove the original console panel with a plastic knife, pry gently along the gap and pick up the panel. Then set it aside.

1. Remove the original console panel with a plastic knife

1. Remove the original console panel with a plastic knife

 

2·Remove the four screws that fixed the radio on the dashboard. Remove these screws will not be a difficult job.

2. Remove the four screws that fixed the radio on the dashboard

2. Remove the four screws that fixed the radio on the dashboard

 

3·Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

3. Pull the factory radio out of the dash

3. Pull the factory radio out of the dash

 

4·Unplug the connectors.

4. Unplug the connectors

4. Unplug the connectors

 

5·Remove the brackets on both sides of the factory radio. So far the removal of the factory radio is completed. Next steps will move to the installation of the Seicane stereo.

5. Remove the brackets on both sides of the factory radio

5. Remove the brackets on both sides of the factory radio

 

6·Install the brackets on both sides of the Seicane stereo.

 

7·Dock the connectors of the original vehicle and the upgraded car audio.

7. Dock the connectors of the original vehicle and the upgraded car audio

7. Dock the connectors of the original vehicle and the upgraded car audio

 

8·Insert the wires to the appropriate location of the upgraded radio. If you are not sure about how to wire correctly, you may refer to the wiring diagram for details.

 

9·Fix the Seicane radio with the four screws.

7. Dock the connectors of the original vehicle and the upgraded car audio

7. Dock the connectors of the original vehicle and the upgraded car audio

 

10·Firm the console panel. Finally the new Seicane stereo is installed and a comprehensive test should be conducted on the new stereo.

7. Dock the connectors of the original vehicle and the upgraded car audio

7. Dock the connectors of the original vehicle and the upgraded car audio

 

Wish you can get some help from the above installation guide for a Mitsubishi Universal car stereo. It is not too difficult to install a new car stereo in your car. If you can’t do it on your own, please ask a professional to help. Besides, you need to find a suitable stereo as well. If you don’t have one, it’s wise of you to take this intelligent Mitsubishi Universal car stereo into consideration, please click for more details:

 

http://www.seicane.com/aftermarket-android-touch-screen-gps-navigation-system-for-2012-mitsubishi-universal-support-bluetooth-radio-tpms-dvr-obd-ii-rear-camera-aux-headrest-monitor-control-usb-sd-hd-1080p-video-3g-wifi-s086991

 

This Mitsubishi Universal car stereo comes with a worldwide real-time GPS navigation system let you go anywhere without getting lost with its most accurate direction and spoken guidance. To simply pair your compatible mobile phone with this stereo, you are allowed to make and receive hands-free calls and stream your favorite music from the playlist in your cell phone or other portable devices.

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander.

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander

Car stereo audio after installation,dvd GPS navigation system of 2006-2011 Mitsubishi outlander

Upgrading car stereos can be a self-done thing in recent years,because there are a lot of materials on the Internet which can help you achieve this goal.

So if you are a owner of 2006-2011 Mitsubishi outlander,installing a dvd player with navigation system for your car by yourself is also very possible to realize when you have known easy installation steps for 2006-2011 Mitsubishi outlander navigation system support Mp3 Mp4.

Before you upgrade car audio system,you need to make adequate preparations for this process.Such as reading some essaies,watching videos,visiting some websites and so on.And you need to make these preparations including preparing removal tools after you have made it very clear.

Another question that you have no idea is that whether the aftermarket Mitsubishi outlander navigation system fits your car,here is a method for you:have a careful look at its trim panel and see if it’s same with your factory one’s.

2006-2011 Mitsubishi outlander car stereo removal and installation:

1.Open up the glove compartment

Open up glove compartment

Open up glove compartment

2.Get out screw to side panel,then remove side panel

Get out screw to side panel

Get out screw to side panel

3.Gently drag trim piece toward seat place

remove side panel by pulling toward seat

remove side panel by pulling toward seat

5.Use panel removal tool,gently pry edges around stereo face

use your hand or panel removal tool,gently pry around edges of stereo face

use your hand or panel removal tool,gently pry around edges of stereo face

6.Disconnect this cable,and do not start your car at that time

Disconnect the connector

Disconnect the connector

7.Get four screws holding stereo in place out

Make out four screws holding stereo in place

Make out four screws holding stereo in place

8.Get out stereo for access to harnesses behind it

Get out stereo for access to harnesses behind it

Get out stereo for access to harnesses behind it

9.Get out smaller connector to give access to Grom Y-harness, plug Grom harness into open port, connect removed harness to Grom Y-harness, Make 20-pin harness connected to Grom unit

Get out smaller connector to give access to Grom Y-harness

Get out smaller connector to give access to Grom Y-harness

plug Grom harness into open port

plug Grom harness into open port

connect removed harness to Grom Y-harness

connect removed harness to Grom Y-harness

Make 20-pin harness connected to Grom unit

Make 20-pin harness connected to Grom unit

10.Use provided P-Tap to make connection,please have a check that if P-Tap has punctured wire and is tightly secured

Use provided P-Tap to make connection

Use provided P-Tap to make connection

11.Plug stripped wire in as far as possible as the picture show

Plug stripped wire in as far as possible as the picture show

Plug stripped wire in as far as possible as the picture show

12.Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

13.After finishing cables connection,turn on new stereo and check new unit and hope that you can enjoy a good time with new audio system

I guess most of you are not very clear about operations for this dvd,you can visit next website for more detailed usful knowledge: http://www.seicane.com/digital-touch-screen-car-dvd-player-gps-navigation-specialized-for-2006-2011-mitsubishi-outlander-with-radio-bluetooth-usb-sd-3g-wifi-c056.

If you are also interested in the installation affairs about Mitsubishi L200 navigation,you can go to and have a look at it.

 

 

 

 

Have you covered some materials about upgrade for 2010 2011 Mitsubishi Lancer autoradio?If you are interested in installing a new head unit into your car,then you answer is probably yes.And today I’d like to show you specific installation steps for 2010 2011 Mitsubishi Lancer double din radio dvd support HD 1080P video.

Let’s have a look at a picture first,which is new unit after installation,GPS dvd player with touch screen rearview camera of 2010 2011 Mitsubishi Lancer.Showing this image is to provide a comparison for you to judge that if this unit can be installed in your car though you are not a owner of 2010 2011 Mitsubishi Lancer.

new unit after installation,GPS dvd player with touch screen rearview camera of 2010 2011 Mitsubishi Lancer

new unit after installation,GPS dvd player with touch screen rearview camera of 2010 2011 Mitsubishi Lancer

It’s not right to hold that a stereo is only for one car,while it may fit several cars actually,this is very possible.And the principles of it are almost same and has little difference.Thus on matter whether this nav radio installation guide is just for you,you can still have a patient reading and learn something which will benefits you.

We can see that roads are increasing very rapidly and become more complex,so GPS navigation system is very necessary to most drivers,it’s difficult for us to remember all routes in a place especially when we are in a strange place.Therefore many people begin to realize the importance of it.But they are too busy or don’t know how to achieve it,so many willing drivers haven’t achieved this goal.

And today I will give you some advices on how to remove and install the head unit of 2010 2011 Mitsubishi Lancer.Don’t be afraid of following number for step,in fact they are not hard to behave.

2010 2011 Mitsubishi Lancer radio head unit removal and installation:

1.Open up glove box

Open up glove box

Open up glove box

2.Take screw out to side panel

Take screw out to side panel

Take screw out to side panel

3.Take side panel out by pulling toward seat

Take side panel out by pulling toward seat

Take side panel out by pulling toward seat

4.Take screw out to trim panel

Take screw out to trim panel

Take screw out to trim panel

5.Pull trim piece toward seat softly

Pull trim piece toward seat softly

Pull trim piece toward seat softly

6.Once trim piece is released,remove trim panel with panel removal tool or your hands

remove trim panel with panel removal tool or your hands

remove trim panel with panel removal tool or your hands

7.Several clips across trim panel which holds trim piece in place

Several clips across trim panel which holds trim piece in place

Several clips across trim panel which holds trim piece in place

8.Please note that do not take these three screws out

do not take these three screws out

do not take these three screws out

9.Gently prize around edges of stereo face with panel removal tool

Gently prize around edges of stereo face with panel removal tool

Gently prize around edges of stereo face with panel removal tool

10.After removing stereo face,tab along edges of stereo which hold stereo

tab along edges of stereo which hold stereo

tab along edges of stereo which hold stereo

11.Disconnect the cable,and do not turn on vehicle at that time

Disconnect the cable

Disconnect the cable

12.Take four screws holding stereo in place out

Take four screws holding stereo in place out

Take four screws holding stereo in place out

13.Take stereo out for access to harnesses behind it

Take stereo out for access to harnesses behind it

Take stereo out for access to harnesses behind it

14.Take smaller connector out to give access to Grom Y-harness

Take smaller connector out to give access to Grom Y-harness

Take smaller connector out to give access to Grom Y-harness

15.Make Grom harness into open port connected

Make Grom harness into open port connected

Make Grom harness into open port connected

16.Plug harness which is removed to Grom Y-harness

Plug harness which is removed to Grom Y-harness

Plug harness which is removed to Grom Y-harness

17.Connect 20-pin harness to Grom unit

Connect 20-pin harness to Grom unit

Connect 20-pin harness to Grom unit

18.Separate and check wire for +12v constant

Separate and check wire for +12v constant

Separate and check wire for +12v constant

19.With+12v constant confirmed,make connection with provided P-Tap,please ensure P-Tap has punctured wire and is tightly secured

make connection with provided P-Tap

make connection with provided P-Tap

20.Fasten top cap and then connect Yellow power wire

Fasten top cap and then connect Yellow power wire

Fasten top cap and then connect Yellow power wire

21.Plug stripped wire as far as possible

Plug stripped wire as far as possible

Plug stripped wire as far as possible

22.Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

Secure cap tightly and tug on wire to ensure it is secured

23.After making all connections,turn on stereo and test new unit and hope that you can enjoy your new audio system

Please check radio appearance and all functions to make sure they can work well before you start to upgrade car stereo and replace a new unit.After that you only can start up to make your Mitsubishi Lancer radio more wonderful by yourself.

If you need to know more details about new features of new installed dvd display,you can visit the following website which has a lot of information there: http://www.seicane.com/double-din-2010-2011-mitsubishi-lancer-aftermarket-gps-radio-system-tv-tuner-cd-dvd-player-3g-wifi-pop-dvr-hd-1080p-video-backup-camera-ipod-iphone-c037.

 

2006-2013 Mitsubishi L200 dvd gps sat nav system installation is a little different from other stereos’ installation,because this kind of stereo include two things:one touch screen and one operation system.It means that you can use the radio not only by using touch screen pen but also by operate push buttons.

Actually this kind of stereo is not only just for Mitsubishi L200,it can also be installed in cars of Mitsubishi Triton,Mitsubishi Pajero Sport,Mitsubishi Montero Sport,Mitsubishi Nativa,Mitsubishi Pajero Dakar from 2006-2013.Because these cars’ radio dashboard are same to stereo dashboard of Mitsubishi L200.

It sounds great,isn’t it?And, if you decide to remove original head unit of the car and mount a bluetooth dvd,here are specific steps on removing autoradio that may help you finish your installation work.

1..Original car stereo

original car stereo

original car stereo

2.Remove this screw and the other one on the left

remove this screw and the other one on the left

remove this screw and the other one on the left

3.With two screws removed,you can easily remove the trim panel

easily remove the trim panel

easily remove the trim panel

4.Remove four screws which has two on each side(on this side is the screw in the picture and lower one),and put them on a prominent place

remove four screws which has two on each side

remove four screws which has two on each side

5.Then the stereo is unclipped,but remember to turn off your car and make your hanging file to empty file in order to make sure security

turn off your car and make your hanging file to empty file

turn off your car and make your hanging file to empty file

6.Unplug cables that connected the stereo

unplug cables that connected the stereo

unplug cables that connected the stereo

7.Remove these two screws and the other two behind them and then you can remove trim panel of the stereo

remove these two screws and the other two behind them

remove these two screws and the other two behind them

8.Connect cables and antennas of new radio correctly to the car

9.Tidy all wires well,firm 4screws to make sure secured and install new unit into it

10.Firm four removed screws and install dashboard on the radio

This is aftermarket sat navi system dvd player of 2006-2013 Mitsubishi L200,which is a little special than other ones,and if your radio set is like this one,then you can mount it in your car under correct installation guide.

stereo autoradio after upgrade,aftermarket sat navi system dvd player of 2006-2013 Mitsubishi L200

aftermarket sat navi system dvd player of 2006-2013 Mitsubishi L200

After you have finished all this for Mitsubishi L200 dvd gps installation,you can turn on the new radio and check whether this new unit can work or not.If yes,it means that you have achieved it successfully.But if it doesn’t work,then you may need to find out the reason and check your operations including cable connection,whether screws are tight or you lose something which is important.If you are willing to search the Internet,I advise you to visit some useful websites,for example:

http://www.seicane.com/all-in-one-cd-dvd-radio-gps-stereo-for-2006-2013-mitsubishi-l200-triton-pajero-sport-montero-sport-nativa-pajero-dakar-with-lcd-touch-screen-dvd-bluetooth-tv-tuner-3g-wifi-mp3-steering-wheel-control-pop-dvr-aux-c094  .

The dvd player has a lot of features,especially the GPS navigation system.GPS has become a hot trend in drivers,for it bring them much convenience when they are busy in the car,and it also make you have a closer connection with outside world.Surely you will enjoy good time with a new head unit in your car.If you meet any problems,ask people who are professional in this market for help.