Car Dvd VW | car dvd blog

22Mar 2016

Install a 2011 2012 2013 VW Volkswagen New Beetle 2 radio with easy 8 steps

2011 2012 2013 VW Volkswagen New Beetle 2 radio after installation

After getting an ideal head unit for your car, you must want to install it immediately, so that you can enjoy the new features and have a different driving experience. Some car owners may choose to install it by themselves in order to save money. However, incorrect installation may cause unexpected damage, therefore, you’d better ask a professional for help if you don’t have any experience on it. The picture below is the latest 2011 2012 2013 VW Volkswagen New Beetle 2 radio from Seicane, if you have the same dashboard, you can take this installation guide as a reference.

2011 2012 2013 VW Volkswagen New Beetle 2 radio after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

2011 2012 2013 VW Volkswagen New Beetle 2 radio installation guide

Step1: Remove the trim panel.

Please pry around the trim panel with a lever. While prying, please loosen the trim panel with your hand. When the trim panel is loosened, please remove the trim panel off the dashboard and gently place it aside for further removal.

2011 2012 2013 VW Volkswagen New Beetle 2 radio installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new radio.

2011 2012 2013 VW Volkswagen New Beetle 2 radio installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory radio out of the dash.

2011 2012 2013 VW Volkswagen New Beetle 2 radio installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of it.

2011 2012 2013 VW Volkswagen New Beetle 2 radio installation step 4

Step 5: Connect the new Seicane radio to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane radio into the dash and install four screws.

Step 8: Install the trim panel into its original place.

Wish the above installation guide can do some help for you. Please make sure you are clear about every step before you start to install. If you find it too hard to understand all the steps, you ‘d better have your new radio installed by a professional or go to a car stereo upgrade center for help.

Moreover, you need to be clear that your new radio can be compatible with your car. If you don’t have an ideal one, I’d like to recommend an up-to-date 2011 2012 2013 VW Volkswagen New Beetle 2 radio from Seicane to you. Here’s the link:

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

This VW Volkswagen New Beetle 2 radio supports almost all the popular audio and video formats, such as DVD/VCD/CD/MP3/MPEG4/DIVX/CD-R/WMA/JPEG, you won’t feel tired and boring in the long trip any longer. You can easily pair your mobile phone with this unit for wireless communication with your callers by keeping your hands still on the steering wheel control. Just enjoy your favorite music and navigate to your destination with this amazing GPS navigation system.

Just go with this remarkable VW Volkswagen New Beetle 2 radio and have a wonderful time on all your trips from now ons!

22Mar 2016

A step-by-step installation guide for a 2010-2013 VW Volkswagen Multivan car stereo with DVD player touch screen 1080p video GPS

eric ⋅ Leave a Comment

2010-2013 VW Volkswagen Multivan car stereo after installation

To install a new car stereo to replace the factory radio on one’s own not only saves money but also raises the sense of achievement, therefore, more and more car owners try to install the new car stereo on their own and they did it finally. If you have some related installation experience and a correct installation guide, you can also achieve it by yourself. Please look at the picture below, it’s a modern 2010-2013 VW Volkswagen Multivan car stereo from Seicane, if your dashboard is the same as it, you can take this VW Volkswagen Multivan car stereo installation guide as a reference.

2010-2013 VW Volkswagen Multivan car stereo after installation

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

2010-2013 VW Volkswagen Multivan car stereo installation guide

Step1: Remove the trim panel.

2010-2013 VW Volkswagen Multivan car stereo installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new radio.

2010-2013 VW Volkswagen Multivan car stereo installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory radio out of the dash.

2010-2013 VW Volkswagen Multivan car stereo installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of it.

2010-2013 VW Volkswagen Multivan car stereo installation step 4

Step 5: Connect the new Seicane car stereo to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane car stereo into the dash and install four screws.

Step 8: Install the trim panel into its original place.

The installation is actually quite easy. Wish the above installation guide can do some help for you. If you have any questions, please consult your dealer or a professional for help. If you find the dashboard above is different from yours, please don’t worry, it won’t have much influence on the installation. If it’s the first time for you to install a new car stereo, you’d better go to a car stereo upgrade center or ask a professional for help.

What’s more, you need to pick a right stereo for you car to ensure it can be installed in your car without any gap. If you don’t have one, you can refer to an amazing 2010-2013 VW Volkswagen Multivan car stereo from Seicane, please click the following link:

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

This VW Volkswagen Multivan car stereo comes with a 3D GPS navigation system of high precision, you are allowed to go anywhere without getting lost any more. Thanks to the advanced Bluetooth technology, you can simply pair your mobile phone with this unit for having hands-free calls and enjoying music streaming from the playlist in your phone or other portable devices.

Improve your in-car environment and driving experience to next level, this intelligent VW Volkswagen Multivan car stereo is just your best choice. Just go and enjoy the wonderful time with it in your beloved car.

17Mar 2016

How to replace a 2005-2012 VW Volkswagen PASSAT head unit with 3G WiFi Mirror Link OBD2 Bluetooth DVD player

eric ⋅ Leave a Comment

First shows you a modern 2005-2012 VW Volkswagen PASSAT head unit from Seicane after installation. it looks cool, doesn’t it?

2005-2012 VW Volkswagen PASSAT head unit after installation

Some car owners may think it very hard to install such a unit in their cars. As a matter of fact, if you have some related installation experience and a correct installation guide, you can also finish the installation on your own. However, if you are a green hand, you’d better have it installed. Anyway, you can refer to the following 2005-2012 VW Volkswagen PASSAT head unit installation guide to better help with your installation of your new head unit if you have the same dashboard as that shown in the image above.

Precautions for this installation:

1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2.Please make sure that all fastened wires are isolated with electrical tape.

3.Please make sure the ignition is off to avoid short circuit.

2005-2012 VW Volkswagen PASSAT head unit installation guide

Step1: Remove the trim panel.

2005-2012 VW Volkswagen PASSAT head unit installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new radio.

2005-2012 VW Volkswagen PASSAT head unit installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory radio out of the dash.

2005-2012 VW Volkswagen PASSAT head unit installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of it.

2005-2012 VW Volkswagen PASSAT head unit installation step 4

Step 5: Connect the new Seicane head unit to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane head unit into the dash and install four screws.

Step 8: Install the trim panel into its original place.

That’s all the installation guide for the 2005-2012 VW Volkswagen PASSAT head unit. If you don’t understand well, you can ask your dealer or a professional for help. Please make clear every step before you start to install it. And you can go to a car stereo upgrade center to install it if you find it too hard to do it on your own.

In addition, to have a successful upgrade, it’s necessary for you to make sure your new head unit can fit your car. If you have no idea about this, you can take the following Seicane 2005-2012 VW Volkswagen PASSAT head unit as a reference, which can be installed in your 2005-2012 VW Volkswagen PASSAT without any gap. Here’s the link:

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

This multifunctional VW Volkswagen PASSAT head unit is designed with a large 8 inch 1024*600 multi-touch screen to simplify the operation and facilitate the performance.

You can go anywhere with the accurate guidance and turn-by-turn direction provided by the GPS navigation system. Coming with built-in/external Microphone, you can listen to your favorite music in your mobile phone or iPod through your car’s speakers. Bluetooth hands-free calls are also available for you to make yourself and your passengers safe all the way.

Just install this wonderful VW Volkswagen PASSAT head unit in your car and enjoy a different driving experience from now on!

26Feb 2016

A detailed installation guide for a 2006-2011 VW Volkswagen Cupra car stereo with Bluetooth Quad-core CPU 16G Flash

eric ⋅ Leave a Comment

With the improvement of technology, you can easily find what you need in your car in new aftermarket car stereo. If your factory radio is far enough to meet your requirements in your car, then it’s wise of you to replace it with a new car stereo. The picture below is an advanced 2006-2011 VW Volkswagen Cupra car stereo from Seicane, if you have the same dashboard, you can take the following detailed installation guide as a reference.

2006-2011 VW Volkswagen Cupra car stereo after installation

Precautions:

Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure safety.
A lever and a screwdriver need to be prepared before the installation.

2006-2011 VW Volkswagen Cupra car stereo installation guide

Step1: Remove the trim panel.

2006-2011 VW Volkswagen Cupra car stereo installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new radio.

2006-2011 VW Volkswagen Cupra car stereo installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory radio out of the dash.

2006-2011 VW Volkswagen Cupra car stereo installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of it.

2006-2011 VW Volkswagen Cupra car stereo installation step 4

Step 5: Connect the new Seicane car stereo to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane car stereo into the dash and install four screws.

Step 8: Install the trim panel into its original place.

Wish the above installation guide can be helpful for you. If you find the factory radio is different from yours, don’t worry, it’s normal that cars in different manufacture years come with different dashboard. But it won’t have much impact on the installation which is similar on the whole. If you have any questions, you can turn to your dealer or a professional for help.

Because different car stereos are specific for different cars, you need to find a suitable car stereo for your car so that it can work well and be installed perfectly. If you don’t find one, you can refer to the following link which is a modern VW Volkswagen Cupra car stereo from Seicane.

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

This VW Volkswagen Cupra car stereo comes with a built-in GPS system, you won’t worry about getting lost in an unfamiliar place any more. And you can keep safe and relaxed all the way if you wirelessly link your Bluetooth-enabled cell phone to this unit to have hand-free conversations with your callers and stream music from the playlist of your phone.

What’s more, other popular audio and video formats such as DVD/VCD/CD/MP3/MPEG4/DIVX/CD-R/WMA/JPEG can work with this unit to let you have more options to entertain both yourself and your passengers.

Just install this remarkable VW Volkswagen Cupra car stereo in your car and enjoy the amazing convenience and great enjoyment it brings to you.

22Jan 2016

9 easy steps to upgrade a 2012 2013 2014 VW Volkswagen Passat CC head unit with a Quad-core CPU 16G Flash DVD GPS

eric ⋅ Leave a Comment

If you are a car owner of 2012 2013 2014 VW Volkswagen Passat CC, you must want to have a comfortable car life and enjoy the greatest convenience in your car while you are driving. How can you get both of them at the same time? Just upgrade your factory radio with an all-in-one head unit. You will enjoy the greatest fun as well as the convenience it brings to you. Look at the following picture, which is a Seicane 2012 2013 2014 VW Volkswagen Passat CC head unit after installation. If you have the same or similar dashboard, you can follow the detailed installation instructions to help you with your upgrading.

2012 2013 2014 VW Volkswagen Passat CC head unit after installation

There are some precautions before installation:

Ensure the power cable is disconnected for safety.
Make sure the ignition is off to avoid short circuit and connect the yellow and res cable at last before connecting.

2012-2014 VW Volkswagen Passat CC head unit installation guide

1)Lift the latch at the bottom of the decoration panel.

2012 2013 2014 VW Volkswagen Passat CC head unit installation step 1

2) Remove four screws holding the original radio into the dashboard on the left and right sides with a screwdriver.

2012 2013 2014 VW Volkswagen Passat CC head unit installation step 2

3) Take the factory radio out of the dashboard, then unplug all the connectors exposed at the back of it.

2012 2013 2014 VW Volkswagen Passat CC head unit installation step 3

4) Connect the GPS aerial for new Seicane head unit and the rearview camera connectors (optional).

2012 2013 2014 VW Volkswagen Passat CC head unit installation step 4

5)Connect the new Seicane radio aerial conversion lines with the factory radio aerial.

6)Plug the connectors to the new Seicane head unit.

7)Connect all the harness, put the new Seicane head unit into the dash, and fix all the screws.

8)Install the decoration panel and push it inside until the latch lock it.

9)Turn on the new Seicane head unit to conduct a comprehensive check if all functions work well.

The installation is actually quite easy. But if you have no such experience at all, you’d better do it under the guidance of a professional. Before the installation, you need to figure out every step so as to make your removal and installation successful.

Besides, you have to confirm the compatibility of the new head unit with your car. Only a fitting head unit can be perfectly installed and work well with your car. If you don’t have a suitable head unit, I’d like to recommend a good 2012 2013 2014 VW Volkswagen Passat CC head unit from Seicane to you.

http://www.seicane.com/seicane-s121011-10-2-inch-android-4-4-4-radio-dvd-head-unit-gps-system-for-vw-volkswagen-passat-cc-with-quad-core-cpu-16g-flash-bluetooth-mirror-link-obd2-3g-wifi-rearview-camera-dual-way-canbus-aux

This VW Volkswagen Passat CC head unit is designed as the original radio, so it can be installed in your car seamlessly. With a large 10.2 inch HD 1024*600 multi-touch screen, it’s easy to operate and ideal for viewing.

The GPS navigation system provides the accurate direction for you to travel to your destination on time. You can wirelessly pair your Bluetooth cell phone with this unit to have hands-free calls and streaming music, which can bring you an absolutely safe and pleasant journey all the time.

Under a big discount right now, it’s wise of you to take this VW Volkswagen Passat CC head unit without any hesitation. Wish you will enjoy your upgrading and have a good time!

16Jan 2016

An easy upgrading guide of a 2004-2011 VW Volkswagen Sagita head unit with Bluetooth wifi DVD player GPS navigation

eric ⋅ Leave a Comment

When the idea comes up to your mind that buying a new VW Volkswagen Sagita head unit to replace your factory radio for advanced configurations as well as a brand new driving experience, you may think about the question of its installation. Some car owners may think one needs much expertise to install a new car head unit. In fact, that’s not the case. With the correct installation guide and related installation experience, one can easily finish the installation by themselves. If you are going to install your own new head unit by yourself, the following VW Volkswagen Sagita head unit installation guide can be helpful for you.

Precautions:

Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure security.
A lever and a screwdriver need to be prepared before the installation.

Please refer to the below step-by-step removal and installation instructions for 2004-2011 VW Volkswagen Sagita head unit as a reference:

Step1: Remove the trim panel.

Please pry around the trim panel with a lever. While prying, please loosen the trim panel with your one hand. When the trim panel is loosened, please remove the trim panel off the dashboard and gently place it aside for further removal.

2004-2011 VW Volkswagen Sagita head unit installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new head unit.

2004-2011 VW Volkswagen Sagita head unit installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory out of the dash.

2004-2011 VW Volkswagen Sagita head unit installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of the factory radio.

2004-2011 VW Volkswagen Sagita head unit installation step 4

Step 5: Connect the new Seicane head unit to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane unit into the dash and install the four screws.

Step 8: Install the trim panel into its original place.

The installation of this unit is quite easy. However, you need to make clear of every step before the removal and installation. If you think it too difficult to understand, you can ask for a technician to help you with the installation, which may cost you some fee though, it’s good to ensure you can have a successful upgrading.

To make sure the new head unit can be perfectly installed in your car and can work well with your car, you need to buy a suitable VW Volkswagen Sagita head unit. You can browse the following link which is an amazing head unit for e VW Volkswagen Sagita from Seicane.

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

With both hardware and software upgraded, this double din 2004-2011 VW Volkswagen Sagita head unit is an ideal car stereo to replace your factory radio. It mainly features GPS navigation system, DVD player, Bluetooth function, iPod function, USB port, SD card slots, giving you both convenience and exhilaration when you are driving.

Reach your destination on time with the turn-by-turn direction and voice prompts. The Bluetooth technology can support pairing your Bluetooth-enabled cell phone with this unit, so that you can stream music and stay focused on the road ahead and keep your hands on the steering wheel control to have a safe and pleasant driving.

Wish you’ll have a good time with this 2004-2011 VW Volkswagen Sagita head unit! Good luck to you!

15Jan 2016

Upgrade a 2008-2013 VW Volkswagen Scirocco head unit with 8 steps

eric ⋅ Leave a Comment

To enjoy a more entertaining life in a car, more and more people are choosing to upgrade their factory radio with a most up-to-date head unit for more features as well as high performance. Compared with a factory radio, you can enjoy integrated functions in one head unit which easily make your in-car life more convenient and enjoyable. If you are going to replace your factory radio with a 2008-2013 VW Volkswagen Scirocco head unit, this article would be helpful for you to install it in your car with a correct guide.

Precautions:

Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure security.
A lever and a screwdriver need to be prepared before the installation.

Please refer to the below step-by-step removal and installation instructions for 2008-2013 VW Volkswagen Scirocco head unit as a reference:

Step1: Remove the trim panel.

2008-2013 VW Volkswagen Scirocco head unit installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new head unit.

2008-2013 VW Volkswagen Scirocco head unit installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory out of the dash.

2008-2013 VW Volkswagen Scirocco head unit installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of the factory radio.

2008-2013 VW Volkswagen Scirocco head unit installation step 4

Step 5: Connect the new Seicane head unit to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new Seicane unit into the dash and install the four screws.

Step 8: Install the trim panel into its original place.

The above is all the installation guide for a VW Volkswagen Scirocco head unit. With you can get some help from it. If you think it too hard to understand, you’d better have it installed by a professional technician. To make sure you can upgrade your factory radio with success, you need to buy a head unit which can fit your car very well. The following link is a great head unit from Seicane for you as a reference.

http://www.seicane.com/seicane-s128405-8-inch-android-4-4-4-dvd-radio-car-navigation-head-unit-for-2008-2013-vw-volkswagen-scirocco-with-3g-wifi-mirror-link-obd2-bluetooth-quad-core-cpu-16g-flash

With this upgraded in dash DVD player navigation system installed in your car, you can meet all your needs of a car stereo for your VW Volkswagen Scirocco. Built-in GPS navigation system, DVD/CD/MP4/MP3/MP2 player, Bluetooth hands-free calls and streaming music are all supported for you to have a safe and cheerful driving experience.

Wish this article can be helpful for you and you will have a good trip with this VW Volkswagen Scirocco head unit. Good luck!

13Jan 2016

9 Steps to Install 2012 2013 2014 VW MAGOTAN Car stereo

eric ⋅ Leave a Comment

With the improvement of people’s living standards, more and more people can afford a car. Many people will pick a good navigation system after have their own car, just as the old saying: A good horse with a good saddle,yes! Has a navigation system is not enough, but most impotantly, we should know how the system works even though install it for your car by yourself. Now, there is an example about how to install 2012-2014 VW MAGOTAN Car stereo for you .

The first image is Seicane 2012-2014 VW MAGOTAN Car stereo after installtion. It’s beautiful, isn’t it?

2012-2014 VW MAGOTAN Car stereo after installaton

2012-2014 VW MAGOTAN Car stereo installation

1)Lift the latch at the bottom of the decoration panel.

2012-2014 VW MAGOTAN Car stereo installaton step 1

2) Remove the right and left 4 screws.

2012-2014 VW MAGOTAN Car stereo installaton step 2

3) Remove the factory Car stereo, then unplug all the connectors exposed.

2012-2014 VW MAGOTAN Car stereo installaton step 3

4) Well plan the GPS aerial for new Car stereo and the rear-view camera connectors (optional).

2012-2014 VW MAGOTAN Car stereo installaton step 4

5)Connect the new radio aerial conversion lines with the factory radio aerial.

6)Plug the connectors.

7)Well plan all the harness, put the new Car stereo into the dash, fix all the screws.

8)Mount the decoraton panel and push it inside until the latch lock it.

9)Replacement finished and turn it on to test all the functions.

There are some precautions before installation:

Ensure the power cable is disconnected for safety reasons

Make sure the ignition is off to avoid short circuit and connect the yellow and res cable at last before connecting.

If you meet the questions that you don’t know, you can consult professionals for help.

The 2012-2014 VW MAGOTAN car stereo it’s getting trendy in car owners,it with Pure android 4.4.2 operating system and R16 1.6 GHz Quad-core, also support many functions such as : DVD player, TPMS, External TV tuner, 3G module, Mirror Link, Rearview camera, DVR, OBDⅡ. 10.2 inch 1024×600 HD big screen can bring owners a new feeling where use GPS navigation or watch movie.

If you don’t have a this Car stereo and want to know more detail functions about 2012-2014 VW MAGOTAN car stereo, you can visit this link from Seicane :

http://www.seicane.com/10-2-inch-aftermarket-android-radio-gps-navigation-system-for-2012-2013-2014-vw-volkswagen-magotan-with-capacitive-touch-screen-tpms-dvr-obd-ii-headrest-monitor-control-usb-sd-bluetooth-3g-wifi-video-aux-rear-camera-s081699

Sometimes, you may ask which unit compatible with my car? You can refer to the years and models listed on our Seicane official website. If you’re not sure, you can send a picture of your car’s dashboard including the year and model to sales@seicane.com. Then, we will help you to check it.

30Nov 2015

Upgrade your 2012 2013 2014 Volkswagen Beetle car stereo in 8 steps

eric ⋅ Leave a Comment

Being a straightforward job, to install a new car stereo in your 2012 2013 2014 Volkswagen Beetle can totally be done by cars owners at their home. But if you are a green hand on this, you can turn to a professional technician for help. Besides, a wiring diagram specially made for 2012 2013 2014 Volkswagen Beetle car stereo from your dealer would be great help during the process of the installation.

2012 2013 2014 Volkswagen Beetle car stereo after installation

Precautions:

Please apply the parking brake and remove the negative cable on the vehicle battery before the removal to ensure security.
A lever and a screwdriver need to be prepared before the installation.

Please refer to the below step-by-step removal and installation instructions for 2012 2013 2014 VW Volkswagen Beetle car stereo as a reference:

Step1: Remove the trim panel.

2012 2013 2014 Volkswagen Beetle car stereo installation step 1

Step2: Remove the four screws on the radio.

Please unscrew the four screws which are holding the radio at four corners with a screwdriver. Then keep them well in a small box for the installation of a new head unit.

2012 2013 2014 Volkswagen Beetle car stereo installation step 2

Step3: Take the factory radio out of the dash.

After the four screws are unscrewed, you can easily pull the factory out of the dash.

2012 2013 2014 Volkswagen Beetle car stereo installation step 3

Step4: Disconnect the wiring harness.

Before you put the factory radio aside, please disconnect the wiring harness at the back of the factory radio.

2012 2013 2014 Volkswagen Beetle car stereo installation step 4

Step 5: Connect the new Seicane head unit to the original wiring harness as the user manual or the wiring diagram shows.

Step 6: Turn on the new Seicane unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

Step 7: Put the new unit into the dash and install the four screws.

Step 8: Install the trim panel into its original place.

All in all, the whole process of the removal and the installation is quite easy. If you still have any questions, you can seek help from your dealer who may give you more detailed instructions. To buy an ideal 2012 2013 2014 Volkswagen Beetle car stereo, you can refer to the following unit from Seicane as a best option:

http://www.seicane.com/seicane-s09004-oem-android-4-4-4-gps-navigation-dvd-player-canbus-radio-for-vw-volkswagen-with-obd2-bluetooth-touch-screen-dvr-backup-camera-tv-usb-sd-hd-1080p-video-wifi-steering-wheel-control-quad-core-cpu-mirror-link

This top unit for 2012 2013 2014 Volkswagen Beetle car stereo can be called the king of in-car systems and it’s not just a name but the upgraded configuration and capabilities prove it is a real king of the head unit for 2012 2013 2014 Volkswagen Beetle. With a large 7 inch multi-touch screen which comes with a flawless high definition display, you can freely play DVD from every country in the world to relax yourself and your passengers during a long and tiresome journey. Take this amazing 2012 2013 2014 Volkswagen Beetle car stereo with you on all trips to have fun!

09May 2015

How to install 2003-2010 VW Touareg navigation dvd with TV tuner aux

jeen ⋅ Leave a Comment

This is car stereo autoradio after installation, radio GPS stereo of 2003-2010 VW Touareg.

stereo autoradio after installation, radio GPS stereo of 2003-2010 VW Touareg

If you are careful enough you will find that people are more likely to seek more pleasure from busy life,and get it from cars is a prefer choice to a lot of people.

Many people are more willing to buy a new car because it will bring them much convenience and entertainments.If you are one owner of 2003-2010 VW Touareg,this article will show general steps which is about how to install 2003-2010 VW Touareg navigation dvd with TV tuner aux.

We can have a careful look at above picture first and make a comparison between your car stereo with it before we get to know how to upgrade original CD player to a new one, and see whether the dashboards of them are alike.If they are in same scale.it shows that this stereo radio can also be installed in your car.I guess most of you have no idea about how to use this stereo,here is a video for you which will show you detailed operations:

This process is not hard actually,but easy doesn’t mean that we have no need to attention any notes,please turn off all affairs of your car to ensure the safety.And you need to note whether dvd player enters heat protection mode when your car has operated at very fast speed for a long time or when you feel the temperature of the stereo is very high.

When you really decide to install a VW Touareg navigation system for your beloved car,you can have a good look at the following VW Touareg radio installation instruction and operate it step by step.

2003-2010 VW Touareg head unit removal and installation:

1.Original VW Touareg dashboard

Original VW Touareg dashboard

2.Insert four small removal tools into the gap of radio

Insert four small removal tools into the gap of radio

3.Tight them into the gap and then get out CD player by pulling off the tools

Tight them into the gap and then get out CD player by pulling off the tools

4.Use a tool as next picture show to loosen lever and then you can remove four levers

Use a tool as next picture show to loosen lever

5.Make the big cable unplugged

Make the big cable unplugged

6.Release this screw with a small special tool and plug most fine wire to it

Release this screw with a small special tool

plug most fine wire to it

7.Get out inner wire and take a blue one out and then plug it into white one of new unit,with the other white wire plugged into blue one’s original place

Get out inner wire and take a blue one out and then plug it into white one of new unit

with the other white wire plugged into blue one’s original place

8.Plug it to right place,put wires in and turn on the stereo and check whether all functions can work well

plug it to right place

put wires in and turn on the stereo

VW Touareg bluetooth dvd with autoradio gps installation is finished here.Before your work,you should be careful when you are making cables connection and make sure all antennas must be connected to right positions.

After connection, slide the unit into dashboard and then insert the negative cable to the original wiring harness as the steps show. Open new radio and check whether all functions in the unit can work well.

If it doesn’t,check the wires connection or contact with the technicians from the dealer for help,also you can visit some websites which can help you get a better understanding of new stereo, for example:http://www.seicane.com/all-in-one-gps-radio-stereo-replacement-for-2003-2010-vw-volkswagen-touareg-with-3d-navigation-hd-touch-screen-cd-dvd-player-bluetooth-dvb-t-tv-steering-wheel-control-aux-ipod-iphone-c042 .

1 2 Next »

Category Archives: Car Dvd Vw

Install a 2011 2012 2013 VW Volkswagen New Beetle 2 radio with easy 8 steps

A step-by-step installation guide for a 2010-2013 VW Volkswagen Multivan car stereo with DVD player touch screen 1080p video GPS

How to replace a 2005-2012 VW Volkswagen PASSAT head unit with 3G WiFi Mirror Link OBD2 Bluetooth DVD player

A detailed installation guide for a 2006-2011 VW Volkswagen Cupra car stereo with Bluetooth Quad-core CPU 16G Flash

9 easy steps to upgrade a 2012 2013 2014 VW Volkswagen Passat CC head unit with a Quad-core CPU 16G Flash DVD GPS

An easy upgrading guide of a 2004-2011 VW Volkswagen Sagita head unit with Bluetooth wifi DVD player GPS navigation

Upgrade a 2008-2013 VW Volkswagen Scirocco head unit with 8 steps

9 Steps to Install 2012 2013 2014 VW MAGOTAN Car stereo

Upgrade your 2012 2013 2014 Volkswagen Beetle car stereo in 8 steps

How to install 2003-2010 VW Touareg navigation dvd with TV tuner aux

Post Navigation

Recent Posts

Views

Recent Comments

Archives

Subscribe

Categories

Meta