The image below is the Seicane Chrysler Sebring Aspen 300C Cirrus(2015-2010) head unit after installation. It comes with a wide range of practical and entertaining features as well as attractive interface. If you are planning to upgrade your factory radio with a new head unit to improve your in-car environment and driving experience, this Seicane Chrysler Sebring Aspen 300C Cirrus(2015-2010) head unit may be one of you best choices and you can take the following installation guide as a reference to help with this installation.
2005-2010 Chrysler Sebring Aspen 300C Cirrus after installation
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400
2005-2010 Chrysler Sebring Aspen 300C Cirrus head unit installation steps
1. The original car radio.
The original car radio
2. Grab at the bottoming plastic cover, push the bottoming box and release it.
Grab at the bottoming plastic cover, push the bottoming box and release it
3. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.
3-1.Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
3-2
4. Unplug the connectors at the back of panel.
Unplug the connectors at the back of panel
5. Remove four screws that fixed the radio on the dashboard.
Remove four screws that fixed the radio on the dashboard
6. Gently pull the factory radio out of the dash. The unplug the connectors at the back of the factory radio.
Gently pull the factory radio out of the dash. The unplug the connectors at the back of the factory radio
7. Check all the accessories for the new Seicane head unit.
8. Connect the harnesses to the back of the new Seicane head unit.
9. Connect the Seicane head unit to your original head unit ‘s plugs.
10. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
11. Put the new Seicane head unit into the dash.
12. Put everything into their original place. All the installation is done.
During the whole installation process, if you have any questions, you can seek advice from your dealer or ask a professional for help. It is significant for you to make sure you are clear about every step before the installation. If you find it still too hard to understand all the steps, you’d better go to a car stereo upgrade center to have your head unit installed.
First of all, it is necessary for you to check the compatibility between your new head unit and your car. If you don’t have any ideas about it, you cam refer to the following link which is about a great 2005-2010 Chrysler Sebring Aspen 300C Cirrus dvd gps tv stereo from Seicane, please click:
This 2005-2010 Chrysler Sebring Aspen 300C Cirrus head unit from Seicane, comes with both upgraded features and new functions, is ideal for you to upgrade your factory radio.
Featured a built-in GPS system, this head unit can guide you to your destination with turn-by-turn direction and voice prompts. The Bluetooth technology which allows you to get access to hands-free calls, and streaming music is also included in it to keep you safe and cheerful on all trips. Just enjoy more convenience and joyfulness brought by this remarkable head unit in your car. Wish it become your great road companion.
Recent Comments