To improve your car interior environment as well as upgrade your driving experience, you can make full use of your car radio in your car. Thanks to such an ideal car radio, you can get access not only some practical features but also some entertainment features. Thus you will have an unforgettable driving experience. The following is a 1996 1997 1998 1999 2000-2009 Toyota Prado car radio installation instruction from Seicane which can be taken as your reference.
1996 1997 1998 1999 2000-2009 Toyota Prado GPS Bluetooth Car Radio after installation
Before and during installation, you should notice:
1. Before connecting, please make sure the ignition is off to avoid short circuit.
2. Ensure connect the yellow and red power cable at last.
3. Ensure that all loose wires are isolated with electrical tape
4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5. Ensure that all ground is connected to the same place.
6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400
1996 1997 1998 1999 2000-2009 Toyota Prado car radio installation instruction
1. The original car radio.
The original car radio
2. Adjust the shifter lever.
Adjust the shifter lever
3. Use the plastic removal tool to remove the panel and unplug the connector behind.
Use the plastic removal tool to remove the panel and unplug the connector behind
3-1
4. Grab the center nob, remove it and use a screwdriver to unscrew the hidden screw.
Grab the center nob, remove it and use a screwdriver to unscrew the hidden screw
4-1
5. Remove the panel with a plastic removal tool, then unplug the connectors at the back of it.
Remove the panel with a plastic removal tool, then unplug the connectors at the back of it
5-1
5-2
6. Remove screws that are holding the radio.
Remove screws that are holding the radio
7. Release the clips and take out the original car radio.
Release the clips and take out the original car radio
7-1
8. Disconnect connectors and cables at the back of the radio.
Disconnect connectors and cables at the back of the radio
9. Check all the accessories for the new Seicane car stereo.
10. Connect the harnesses to the back of the new Seicane car stereo.
11. Connect the Seicane car stereo to your original stereo’s plugs.
12. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
13. Put the new Seicane car stereo into the dash.
14. Put everything into their original place. All the installation is done.
Above is the 1996 1997 1998 1999 2000-2009 Toyota Prado car radio installation instruction. If you cannot fully understand all the steps, you can seek help from your dealer, someone experienced or a professional technician. Or you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, please do select an ideal car radio for your beloved car. If you have no ideas, here I would like to share a wonderful 1996 1997 1998 1999 2000-2009 Toyota Prado car radio from Seicane with you. For more details, please click:
According to turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system, you are able to easily locate where you are and navigate to any locations you would like to go to accurately. And you can also listen to your favorite music while navigating thanks to this unit’s dual zone function.
Additionally, through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can utilize this unit so as to dial, answer, reject and mute hands-free calls as well as listen to Bluetooth music streaming from your phone music playlists.
This unit is at a very competitive price now.If you like it, just add it to your shopping cart right now!
Recent Comments