Category Archives: Uncategorized

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

If your factory radio cannot satisfy you in car since it cannot be compatible with some upgraded features, you can think about replacing your factory radio with a new aftermarket car radio. This article aims to introduce how to remove the factory radio and install the new car radio in 2010 2011 2012 2013-2015 KIA Sportage, if you own the same or similar dashboard, you can carefully refer to the following installation steps, which may help with the installation.

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2010 2011 2012 2013-2015 KIA Sportage car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Uncover the screw covers on each corner and then remove the two screws with a screwdriver.

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

3. Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back.

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don't forget to disconnect the connectors at the back

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back

4. Remove the panel on the right side of the radio with a plastic removal tool.

Remove the panel on the right side of the radio with a plastic removal tool

Remove the panel on the right side of the radio with a plastic removal tool

5. Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back.

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

6. Remove four screws that are holding the radio on the dashboard.

Remove four screws that are holding the radio on the dashboard

Remove four screws that are holding the radio on the dashboard

7. Take out the original radio and unplug the connectors at the back of it.

Take out the original radio and unplug the connectors at the back of it

Take out the original radio and unplug the connectors at the back of it

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation instruction. If you meet any difficulties and don’t know how to overcome them, please feel free to contact your dealer, communicate with someone experienced or turn to a professional technician for help. If you still think it hard to install the new car radio, you can directly go to a car radio upgrade center to have the car radio installed by a professional technician.

Anyway, before installation, please carefully pick an ideal car radio for your beloved car. Here I’d like to share a remarkable 2010 2011 2012 2013-2015 KIA Sportage car radio from Seicane with you. Fore more details, please click:

https://www.seicane.com/hd-touchscreen-radio-for-2010-2015-kia-spotage-android-with-gps-navigation-audio-system-bluetooth-music-usb-aux-wifi-1080p-tv-mirror-link-dvr-s0495

This car radio is loaded with the stable Android 6.0 operation system and a powerful quad-core CPU processor, therefore, with this car radio installed in your car, you will embrace a much smoother, faster and easier operation experience.

There are a wide range of practical and entertainment features being offered by this all-in-one car radio, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc.

Under the wireless Bluetooth technology, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone.

What are you waiting for? This unit is at a competitive price now. If you like it, just add it to your shopping cart.

2016 Jeep Renegade car radio after installation

If you are fed up with your factory radio, why not remove it and install a new multifunctional one? Since nowadays most car radios are plug and play, it is not very difficult to install the new car radio. This article will mainly introduce how to remove and install the new car radio for 2016 Jeep Renegade. If you own the same or similar dashboard and would like to upgrade your in-car life,  you can carefully read the following installation steps.

2016 Jeep Renegade car radio after installation

2016 Jeep Renegade car radio after installation

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2016 Jeep Renegade car radio installation guide

1. Start by removing the car radio trim panel using a flat pry tool.

Start by removing the car radio trim panel using a flat pry tool

Start by removing the car radio trim panel using a flat pry tool

1-1

1-1

2. Use a screwdriver to remove screws that are holding the radio on the dashboard.

Use a screwdriver to remove screws that are holding the radio on the dashboard

Use a screwdriver to remove screws that are holding the radio on the dashboard

3. Gently pull the original radio out from the dash.

Gently pull the original radio out from the dash

Gently pull the original radio out from the dash

4. Disconnect all the connectors and cables at the back of the radio.

Disconnect all the connectors and cables at the back of the radio

Disconnect all the connectors and cables at the back of the radio

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original radio’s plugs.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane car radio into the dash.

10. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for you. If you are not very clear about every steps before installation, it is suggested that you should consult your dealer, communicate with someone experienced or turn to a professional for help. What’s more, it is necessary for you to pick an ideal car radio for your beloved car. If you have no idea that which kind of car radio can fit your car, you can refer to the following link which is a remarkable 2016 Jeep Renegade car radio from Seicane. For more details, please click:

https://www.seicane.com/2016-jeep-renegade-touchscreen-android-radio-gps-navigation-system-with-usb-bluetooth-wifi-1080p-aux-mirror-link-steering-wheel-control-s04131

This car radio is running on the stable Android 6.0 operation system and a powerful quad-core CPU processor, so it has strong capabilities and performance to be regarded as one of your best choices to replace your factory radio.

Even you don’t have a good sense of directions, you won’t get lost when you travel around an unfamiliar place. Under the guidance of the turn-by-turn directions and voice prompts, you are able to easily know your current locations and navigate to your desired destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Additionally, thanks to the wireless Bluetooth technology, without taking your hands off the steering wheel, you can dial, answer, reject and mute hands-free phone calls as well as enjoy your favorite music streaming from your phone music playlists with the synchronization between your Bluetooth-enabled mobile phone and this car radio.

Wish you like this unit. Good luck!

2006 2007 2008 2009 2010-2012 Suzuki SX4 car radio after installation

If you cannot wait to enjoy a more convenient and enjoyable in-car environment in your car, it will be a wise choice for you to install a new aftermarket car radio to replace your factory radio. With such an idea car radio installed in your car, you will get access to GPS navigation, Bluetooth hands-free phone calls, Bluetooth streaming music, FM/AM radio, etc. While for the installation, you can either go to a car radio upgrade center or turn to a professional technician for help. The following is a 2006 2007 2008 2009 2010-2012 Suzuki SX4 car radio installation guide from Seicane, you refer to it if you own the same or similar dashboard.

2006 2007 2008 2009 2010-2012 Suzuki SX4 car radio after installation

2006 2007 2008 2009 2010-2012 Suzuki SX4 car radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 2008 2009 2010-2012 Suzuki SX4 car radio installation guide

1. The original car radio.

The original car radio

The original car radio

2. Remove two side panels.

Remove two side panels

Remove two side panels

3. Remove four screws that are holding the radio.

Remove four screws that are holding the radio

Remove four screws that are holding the radio

4. Gently pull out the original radio.

Gently pull out the original radio

Gently pull out the original radio

5. Disconnect the connectors and cables at the back of the radio.

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of the installation process about a 2006 2007 2008 2009-2012 Suzuki SX4 car radio? If you haven’t had any ideas, you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard to install the new car radio, you can directly arrange a professional technician to help you install the new car radio. And since it is very crucial for you to select an ideal car radio for your beloved car. If you don’t know which kind of car radio can fit your car well, you can refer to the following link which is a remarkable 2006 2007 2008 2009-2012 Suzuki SX4 car radio from Seicane. For more details, please click:

https://www.seicane.com/hd-touchscreen-android-radio-gps-for-2006-2012-suzuki-sx4-with-bluetooth-music-wifi-audio-system-1080p-video-usb-obd2-mirror-link-dvr-s04142

With the assistance of the worldwide real-time GPS navigation system of high accuracy, this car radio enables you to know your current location and find the right way to reach your desired destinations accurately even if you don’t have good sense of directions. And thanks to this unit’s dual zone function, this unit enables you to listen to your favorite music while navigating.

Besides, through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to your favorite music streaming from your phone music playlists.

What’s more, you can also add a rear view camera to this unit for automatically switching to the parking image while reversing, which can help you gain a safe driving experience to some extent.

Wish you like this unit and good luck to you!

2013 2014 2015 VW Volkswagen Golf 7 car radio after installation

With a modern car radio which supports dual zone function in your car, you can be guided to your destinations accurately and be provided with much enjoyment at the same time. If your factory radio is too old for you to enjoy upgraded and new features, you can replace it with a new multifunctional car radio under the guidance of a detailed installation guide. The following is a 2013 2014 2015 VW Volkswagen Golf 7 car radio installation instruction from Seicane, which can be taken as a reference if you plan to replace your factory radio.

2013 2014 2015 VW Volkswagen Golf 7 car radio after installation

2013 2014 2015 VW Volkswagen Golf 7 car radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

 

2013 2014 2015 VW Volkswagen Golf 7 car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Release the AC control panel.

Release the AC control panel

Release the AC control panel

3. Remove the trim panel with a plastic removal tool.

Remove the trim panel with a plastic removal tool

Remove the trim panel with a plastic removal tool

3-1

3-1

4. Insert four release keys in the removal slots of the radio and pull outwards to release the radio.

Insert four release keys in the removal slots of the radio and pull outwards to release the radio

Insert four release keys in the removal slots of the radio and pull outwards to release the radio

4-1

4-1

5. Disconnect connectors and cables at the back of the radio.

Disconnect connectors and cables at the back of the radio

Disconnect connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

It is not abnormal if you encounter any difficulties before or during the installation. To effectively overcome these difficulties, you can consult your dealer, communicate with someone experienced or turn to a professional for help. Or if you still think the installation process is too complicated, you can directly arrange a professional technician to help you install the new car radio.

However, if you still haven’t got an ideal car radio yet and don’t know how to select a car radio, here I would like to recommend a remarkable 2013 2014 2015 VW Volkswagen Golf 7 car radio from Seicane to you. For more details, please click:

https://www.seicane.com/hd-touch-screen-android-radio-for-2013-2014-2015-vw-volkswagen-golf-7-gps-navigation-system-with-3g-wifi-bluetooth-music-usb-mirror-link-rearview-camera-1080p-video-obd2-s0441

This car radio is running on the advanced Android 6.1 operation system and a strong quad-core CPU processor, which has greatly improve its capabilities and performance. So this car radio can be regarded as one of the best replacements for your factory radio.

Even you drive around unfamiliar places, you won’t get lost any more. Thanks to the high-accuracy 3D GPS navigation function, you can quickly locate where you are and gain the accurate navigation information as well as the shortest cut to get o your desired destinations through turn-by-turn directions and voice prompts. And with this unit’s dual zone function, you can freely enjoy your favorite music while navigating.

With the built-in Bluetooth module, this unit enables you to pair your Bluetooth-enabled mobile phone with it, so you can freely get access to Bluetooth hands-free calls for entertainment and Bluetooth streaming music for enjoyment.

Wish you like this car radio and have a good time with it. Good luck to you!

 

2008 2009 2010 2011-2012 KIA Forte(MT) Bluetooth GPS Car Radio after installation

To take your in-car life up a level, what will you do in your car? As far as I am concerned, you can think about removing your factory radio and installing a new aftermarket car radio for your beloved car. The following is a 2008 2009 2010 2011-2012 KIA Forte(MT) car radio installation instruction from Seicane, which can be taken as your reference if you own the same or similar dashboard and you would like to replace your factory radio so as to upgrade your in-car life.

2008 2009 2010 2011-2012 KIA Forte(MT) Bluetooth GPS Car Radio after installation

2008 2009 2010 2011-2012 KIA Forte(MT) Bluetooth GPS Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2008 2009 2010 2011-2012 KIA Forte(MT) car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2.Pry the left air conditioner vent with a lever, and then remove it.

Pry the left air conditioner vent with a lever, and then remove it

Pry the left air conditioner vent with a lever, and then remove it

3.Pry the right air conditioner vent with a lever, and then remove it.

Pry the right air conditioner vent with a lever, and then remove it

Pry the right air conditioner vent with a lever, and then remove it

4.Unscrew four screws under the a/c vent holding the original car radio with a screwdriver.

Unscrew four screws under the a/c vent holding the original car radio with a screwdriver

Unscrew four screws under the a/c vent holding the original car radio with a screwdriver

5.Gently take the original car radio out of the dash.

Gently take the original car radio out of the dash

Gently take the original car radio out of the dash

6.Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio

Disconnect all connectors at the back of the original car radio

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9.Connect the Seicane car radio to your original car radio ‘s plugs.

10.Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11.Put the new Seicane car radio into the dash.

12.Put everything into their original place. All the installation is done.

 

Please don’t be over worried if you meet any difficulties and don’t know how to overcome them. To overcome these difficulties, you can contact your dealer, communicate with someone experience or seek help from your dealer. If you still think it hard for you to install the new car radio, you can straightly go to a car radio upgrade center and ask a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to select an ideal car radio for your beloved car. If you have no ideas, you can check out the following link which is a 2008 2009 2010 2011-2012 KIA Forte(MT) car radio from Seicane. For more details, please click:

https://www.seicane.com/hd-touchscreen-android-radio-gps-navi-for-2008-2012-kia-forte-mt-with-bluetooth-music-wifi-usb-1080p-video-mirror-link-s0491

This all-in-one car radio is running on the advanced and stable Android 6.1 operation system and a high-quality quad-core CPU processor. So this unit can provide you with enhance capabilities and better performance so as to taken your in-car life up a level.

Under the guidance of the turn-by-turn directions and voice prompts provided by the 3D GPS navigation function, you can easily know your current locations and find the best route to get to your desired destinations accurately. Besides, this car radio comes with dual zone function, which enables you to freely listen to your favorite music while navigating.

Additionally, though the Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, you are able to dial, answer, reject and mute hands-free phone calls as well as listen to Bluetooth streaming music without taking your hands off the steering wheel.

Wish you like this unit and good luck to you!

2011 2012 2013 2014 BMW X5 E70 X6 E71 CCC car radio after installation

Would you like to own a wonderful driving experience? Or would you like to accurately and punctually find and reach your destinations? And would you like to relax both yourself and your passengers at the back seats all the way? If your answers towards these questions are both “yes”, then you can consider replacing your factory radio with a new aftermarket car radio in your beloved car. The following is a 2011 2012 2013 2014 BMW X5 E70 /X6 E71 CCC car radio installation instruction from Seicane. You can carefully refer to it if you own the same or similar dashboard.

2011 2012 2013 2014 BMW X5 E70 X6 E71 CCC car radio after installation

2011 2012 2013 2014 BMW X5 E70 X6 E71 CCC car radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2011 2012 2013 2014 BMW X5 E70 /X6 E71 CCC car radio installation instruction

1. Press the button that indicated so as to open the glove box.

Press the button that indicated so as to open the glove box

Press the button that indicated so as to open the glove box

1-1

1-1

2. Use a pry tool to pry loose the air vent dash trim.

Use a pry tool to pry loose the air vent dash trim

Use a pry tool to pry loose the air vent dash trim

2-1

2-1

3. Pull out the air-conditioning vent and disconnect the plugs connected behind it.

Pull out the air-conditioning vent and disconnect the plugs connected behind it

Pull out the air-conditioning vent and disconnect the plugs connected behind it

3-1

3-1

4. Then you are going to come the side and pull out the one switch for the actual glove box compartment.

Then you are going to come the side and pull out the one switch for the actual glove box compartment

Then you are going to come the side and pull out the one switch for the actual glove box compartment

5. Use a screwdriver to remove the two screws that fix the original car radio dash trim.

Use a screwdriver to remove the two screws that fix the original car radio dash trim

Use a screwdriver to remove the two screws that fix the original car radio dash trim

5-1

5-1

6. Remove two clips that are behind this radio face.

Remove two clips that are behind this radio face

Remove two clips that are behind this radio face

6-1

6-1

7. Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio.

Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio

Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio

8. Unscrew the screws that fix the original display screen and then remove the screen.

Unscrew the screws that fix the original display screen and then remove the screen

Unscrew the screws that fix the original display screen and then remove the screen

9. Disconnect the connectors at the back of the screen.

Disconnect the connectors at the back of the screen

Disconnect the connectors at the back of the screen

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

That’s the whole removal and installation process of a 2011 2012 2013 2014 BMW X5 E70 /X6 E71 CCC car radio. If there is any problem too complicated for you to deal with, you can contact your dealer, communicate with someone experienced or straightly go to a car radio upgrade centre to have the new car radio installed by a professional technician.While for the car radio selection, if you don’t know which kind of car radios can fit your car well, I’d like to share a fabulous  car radio from Seicane with you. For more details, please click:

https://www.seicane.com/touch-screen-bmw-x5-e70-head-unit-gps-navigation-system-with-ipod-usb-sd-aux-rearview-canbus-srd-8825

With this car radio installed in your beloved car, almost all your needs can be me in car since this unit comes with a wide range of practical and entertainment features, mainly including 3D GPS navigation, FM/AM radio, Bluetooth hands-free calls, Bluetooth streaming music, file management, steering wheel control, etc. And as long as you make full use of these features, you will enjoy great convenience and enjoyment to embrace a new driving experience.

Under the guidance of the turn-by-turn directions and voice prompts provided by the high-accuracy 3D GPS navigation, you can easily locate where you are and find the right way to reach your ideal destinations, so you will not get lost any longer even you are driving around different places and have no sense of directions. .

Wish you like this unit and good luck to you!

2009-2015 BMW X1 E84 car radio after installation

If you would like to improve your driving experience, you can think about removing your factory radio and installing a new aftermarket car radio. While as for the installation, you can search online for a related car radio installation instruction to help you with the installation. The following is a 2009 2010 2011 2012-2015 BMW X1 E84 car radio installation instruction from Seicane, which will provide you with a general understanding of car radio installation. If you own the same or similar dashboard, you can take this instruction as a reference.

2009-2015 BMW X1 E84 car radio after installation

2009-2015 BMW X1 E84 car radio after installation

Here are some tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

 

2009 2010 2011 2012-2015 BMW X1 E84 car radio installation instruction

1. The original dash.

The original dash

The original dash

2. Use a plastic pry tool to loose the panel along with the air vent, and then remove this panel.

Use a plastic pry tool to loose the panel along with the air vent, and then remove this panel

Use a plastic pry tool to loose the panel along with the air vent, and then remove this panel

2-1

2-1

3. Open the panel and disconnect the harzard light,door lock and other connectors at the back.

Open the panel and disconnect the harzard light,door lock and other connectors at the back

Open the panel and disconnect the harzard light,door lock and other connectors at the back

4. Remove the two screws that fix the top panel and then remove this panel.

Remove the two screws that fix the top panel and then remove this panel

Remove the two screws that fix the top panel and then remove this panel

4-1

4-1

5. Pop out the panel around the gear shift and then remove this panel.

Pop out the panel around the gear shift and then remove this panel

Pop out the panel around the gear shift and then remove this panel

6. Unplug the connectors at the back of the climate control.

Unplug the connectors at the back of the climate control

Unplug the connectors at the back of the climate control

7. Unscrew the screws that are holding the radio and then gently remove it.

Unscrew the screws that are holding the radio and then gently remove it

Unscrew the screws that are holding the radio and then gently remove it

8. Disconnect the connectors or cables at the back of the car radio.

9. Check all the accessories for the new Seicane car radio.

10. Connect the harnesses to the back of the new Seicane car radio.

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Wish the above installation steps can be helpful for your installation. If you have any problems, you can contact your dealer, communicate with someone experienced or turn to a professional . Or you can straightly go to a car radio upgrade center to arrange a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to carefully select an ideal car radio for your beloved car. If you have no ideas, you can refer to the following link, which is an amazing 2009 2010 2011 2012-2015 BMW X1 E84 car radio from Seicane.

https://www.seicane.com/android-2009-2015-bmw-x1-e84-hd-touchscreen-car-radio-head-unit-gps-navigation-bluetooth-support-rearview-camera-steering-wheel-control-usb-wifi-mirror-link-obd2-s028219

With this intelligent car radio installed in your car, almost all your needs can be met as long as you make full use of this unit’s practical and entertainment features.

Even you don’t have a good sense of directions, you won’t get lost thanks to this unit’s worldwide real-time GPS navigation system. According to the turn-by-turn directions and voice prompts, you can easily locate where you are and find the optimal route option to arrive at any locations you would like to go to. And this unit comes with dual zone function, which enables you to listen to your favorite music while navigating, and the music will automatically switch to GPS voice.
What’s more, through the Bluetooth connection between this unit and your Bluetooth-enabled mobile phone, you can freely dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlists. So, you will gain a lot of convenience and joyfulness in the driving. Thus, you can get a lot of convenience and joyfulness in the driving process.

Wish you like this unit and good luck to you.

2013 2014 2015 2016 BMW 5 Series F10 F11 NBT car radio after installation

If you would like to drive a car to travel around a city that you are unfamiliar with, you must need high precision GPS navigation function in your car. However, your factory radio may not be advanced enough to be compatible with worldwide real-time GPS navigation function. In that case, it is wise of you to replace your factory radio with a brand new multifunctional car radio for your beloved car. The following is a 2013 2014 2015 2016 BMW 5 Series F10/F11 NBT car radio installation instruction from Seicane which can be taken as your reference.

2013 2014 2015 2016 BMW 5 Series F10 F11 NBT car radio  after installation

2013 2014 2015 2016 BMW 5 Series F10 F11 NBT car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2013 2014 2015 2016 BMW 5 Series F10/F11 NBT car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Use a plastic flat pry tool to pry the air vent panel.

Use a plastic flat pry tool to pry the air vent panel

Use a plastic flat pry tool to pry the air vent panel

3. Use a screwdriver to remove the screws that fix the original car radio panel.

Use a screwdriver to remove the screws that fix the original car radio panel

Use a screwdriver to remove the screws that fix the original car radio panel

4. Remove the car radio panel and then disconnect the connectors at the back of it.

Remove the car radio panel and then disconnect the connectors at the back of it

Remove the car radio panel and then disconnect the connectors at the back of it

5. If you need to remove the original car radio, then just remove these mounting screws and then remove the car radio. Then you should disconnect the connectors at the back of it.

If you need to remove the original car radio, then just remove these mounting screws and then remove the car radio. Then you should disconnect the connectors at the back of it

If you need to remove the original car radio, then just remove these mounting screws and then remove the car radio. Then you should disconnect the connectors at the back of it

6. If you need to remove the screen, then just unscrew the two mounting screws and then remove the screen. And then unplug the connectors or cables at the back of it.

If you need to remove the screen, then just unscrew the two mounting screws and then remove the screen. And then unplug the connectors or cables at the back of it

If you need to remove the screen, then just unscrew the two mounting screws and then remove the screen. And then unplug the connectors or cables at the back of it

6-1

6-1

7. Check all the accessories for the new Seicane car radio.

8. Connect the harnesses to the back of the new Seicane car radio.

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process on a 2013 2014 2015 2016 BMW 5 Series F10/F11 NBT car radio. If you meet any problems, please feel free to contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly go to a car radio upgrade center and ask a professional technician to help you install the new car radio.

If you don’t know how to select an ideal car radio for your beloved car, here I would like to share a remarkable 2013 2014 2015 2016 BMW 5 Series F10/F11 NBT car radio from Seicane with you. For more details, please click:

https://www.seicane.com/hd-touchscreen-android-aftermarket-radio-head-unit-for-2013-2014-2015-2016-bmw-5-series-f10-f11-nbt-car-stereo-gps-navigation-system-bluetooth-phone-wifi-support-obdii-dvr-1080p-video-steering-wheel-control-s028218

With this car radio installed in your car, you can freely get access to a wide range of practical and entertainment features, therefore, almost all your different needs can be met in car thanks to this unit.

This unit comes with 3D GPS navigation function of high precision, so according to its turn-by-turn directions and voice prompts, you can easily locate where you are and navigate to any locations you would like to go to. Additionally, this unit also has dual zone function, so you can freely enjoy your favorite music while navigating and the music will automatically switch to GPS voice.

What’s more, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, without taking your hands off the steering wheel control for a long time, you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlists. Thus,  you will gain a lot of convenience and enjoyment.

What are you waiting for? If you like this unit, please don’t be hesitated to add this car radio to your shopping cart right now.

2012 Honda Civic car radio after installation

An ideal car radio should be compatible with both practical and entertainment features, so it can bring you great convenience and entertainment. If you think your car radio’s functions are too limited, you might as well consider replacing your factory radio with a brand new car radio. This article aims to introduce the installation steps of a 2012 Honda Civic car radio from Seicane. If you own the same or similar dashboard, you can refer to these steps carefully.

2012 Honda Civic car radio after installation

2012 Honda Civic car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2012 Honda civic (LHD) car radio installation instruction

1. Remove the automotive oil table top panel with plastic knife.

Remove the automotive oil table top panel with plastic knife

Remove the automotive oil table top panel with plastic knife

2. Remove the screws under the original car CD.

Remove the screws under the original car CD

Remove the screws under the original car CD

3. Take the original radio out of the dash.

Take the original radio out of the dash

Take the original radio out of the dash

4. Pull the plugs at the back of the original radio.

Pull the plugs at the back of the original radio

Pull the plugs at the back of the original radio

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio’s plugs.

8. Put the new Seicane car radio into the dash.

9. Turn on the new Seicane car radio and check whether the unit is working properly. If not, please check whether all the cables are connected correctly.

10. Install screws and the panel, and put everything into their original place.

 

So now do you have a general understanding of the whole removal and installation steps of a car radio? If you still think it hard to install such a car radio by yourself, it is sincerely suggested that you should seek help from your dealer, someone experienced or a professional. Or you can straightly go to a car radio upgrade center and make the new car radio installed by a professional technician. Additionally, if you are still looking for a suitable car radio but have no ideas, here I would like to share a remarkable 2012 Honda Civic car radio from Seicane with you. For more details, please click:

https://www.seicane.com/seicane-s128201-android-radio-gps-car-audio-system-for-2012-honda-civic-with-cd-dvd-player-bluetooth-music-3g-wifi-mirror-link-obd2-hd-multi-touch-capacitive-screen

This car radio is running on the stable Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance.

With this car radio installed in your car, you will be able to get access to a lot of practical and entertainment features, which can greatly improve your in-car life.

As for the 3D GPS navigation function, what you cannot ignore is that with its help, you can easily know your current locations and accurately find the right way to arrive at any locations you would like to go to according to turn-by-turn directions and voice prompts. And this unit comes with dual zone function, which allows you to listen to your favorite music while navigating.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can freely dial, answer, reject and mute Bluetooth hands-free phone calls as well as Bluetooth streaming music from your phone.

If you like this unit, just don’t hesitate to add it to your shopping cart. Good luck!

2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio after installation

First of all, please look at the following picture. It is a 2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio after installation, which looks amazing, doesn’t it? Here I would like to introduce how to remove the factory radio and install the new car radio for 2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6. If you own the same or similar dashboard and plan to replace a new aftermarket car radio, you can carefully refer to the following 2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio installation steps.

2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio after installation

2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio installation steps

1. The original car radio.

The original car radio

The original car radio

2. Use a plastic pry tool to remove the radio frame.

Use a plastic pry tool to remove the radio frame

Use a plastic pry tool to remove the radio frame

2-1

2-1

3. Use a screwdriver to remove four mounting screws of the radio.

Use a screwdriver to remove four mounting screws of the radio

Use a screwdriver to remove four mounting screws of the radio

4. Gently pull the original radio out from the dash.

Gently pull the original radio out from the dash

Gently pull the original radio out from the dash

5. Disconnect the connectors and cables at the back of the radio.

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original car radio’s plugs, and put the new Seicane car radio into the dash, and fix all the screws.

9. Install the decoration panel and push it inside until the latches lock it.

10. Turn on the new Seicane car radio to conduct a comprehensive check if all functions work well.

 

If you meet any problems that you don’t know how to deal with, it is suggested that you should seek help from your dealer, someone experienced or a professional. If you still think it hard to install the new car radio by yourself, you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, it is very essential for you to carefully pick an ideal car radio. If you have no ideas, here I would like to share a marvelous 2012 2013 2014 VW Volkswagen Magotan B7 Bora Golf 6 car radio from Seicane with you. For more details, please click:

https://www.seicane.com/2012-2013-2014-vw-volkswagen-magotan-android-hd-touchscreen-radio-gps-navigation-system-with-bluetooth-music-audio-mirror-link-wifi-1080p-steering-wheel-control-s0427

This car radio is running on the latest and the most stable Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities, performance and configuration. Besides, this car radio also comes with a lot of practical and entertainment features, which enables you to enjoy great convenience and enjoyment.

With the assistance of the worldwide real-time GPS navigation system, you are able to easily know where you are currently and find the right way to reach your desired destinations according to turn-by-turn directions and voice prompts. Additionally, this unit comes with dual zone function, so you can freely enjoy your favorite music while navigating.

What’s more, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, you can freely get access to Bluetooth hands-free phone calls as well as Bluetooth streaming music.

If you like this car radio, just don’t hesitate to add this unit to your shopping cart.